Rep Power: 0

E-Manage Links for people that need to set theirs up:

EMANAGE: WORKING SETUPS

https://www.civicforums.com/forums/s...d.php?t=217534

https://www.civicforums.com/forums/s...=164441&page=1


Base E-Manage Maps for Turbo'd D17 with working VTEC setup
https://www.civicforums.com/forums/s...d.php?t=196730

Plug & Play harness:
Linky (Thanks 4drcivic2k1)

Wiring schematics for our car:
https://www.civicforums.com/forums/s...d.php?t=155306

VAFC wiring works the same as the E-Manage main harness, minus VTEC:
https://www.civicforums.com/forums/s...d.php?t=169767

E-manage FAQ & Install Tips
http://mohdparts.com/emanage/EmanageFAQ.txt

Outlook of wiring for all 3 harnesses
http://mohdparts.com/emanage/manuals...-manage_10.JPG

E-Manage DIY
https://www.civicforums.com/forums/s...d.php?t=217534



http://mohdparts.com/emanage/install...elp/index.html


THE MYSTERY GRAY WIRE IS TPS, and is pin 15 of terminal A on our harness*


Some wiring tips for the ignition harness:

*pay particular attention to what wires go where (in terms of the INPUT and OUTPUT channels for the emanage) - you don't want to wire the OUTPUT of the emanage to the INPUT of the ECU - you may damage something

*the ignition harness has 8 wires you need to connect - 2 per channel (1 in 1 out), the injector harness has 4 wires you need to connect - 1 per channel.

*On connector A (31 pins) - which should be the very bottom connector on the ECU, pins 27, 28, 29, and 30 are for the ignition coils

*27 = cylinder 4, 28 = cylinder 3, 29 = cylinder 2, 30 = cylinder 1

*so.....channel 1 of emanage goes to cylinder 1, channel 2 to cylinder 3, channel 3 to cylinder 4, channel 4 to cylinder 2

*wire colors of the pins...pin 27 is brown, pin 28 is white/blue, pin 29 is blue/red, pin 30 is yellow/green. For the injectors you only use 4 of the 6 channels. The others you don't wire up.


Some wiring tips for the injector harness:

*wiring info for injectors is as follows: ch1 to pin 5, ch2 to pin 4, ch3 to pin 3 ch4 to pin 2

*Page 23 shows injector haress. Look at the diagram on the left - P/R = ch 4, Y/R = ch 3, O/R = ch 2, etc
http://www.mohdparts.com/emanage/man...-manage_23.JPG

*ignore channel A, B, 5, and 6.


The Support Tool update you'll need:

Update to PC Software v1.13


Firmware for unit update you'll need:

E-manage v1.39 Firmware Upgrade


Problem codes:

2gz-gte e-manage install

 
Rep Power: 412

Alright, I took this post out of another thread in FI. There is a TON of useful info here for people who are setting up the E-Manage. Don't panic, the thread labelled "E-MANAGE: WORKING SETUP FOR EXs!!!" is listed as the first link...

Thanks to Dezod for setting this up. I have added it to the Turbo FAQ in the Forced Induction Forum. If anyone else has any helpful links, feel free to post them here.

-Havok-

 
Rep Power: 510

cool. thanks. can you make a link to this in the turbo faq so it is at easy access int he fi section. mkay

 
Rep Power: 412

 
Rep Power: 0

Your welcome Havok. If anyone thinks anything else needs to be added to this..........post away and I'll add it to the post.

Thanks to Havok for comin thru with the swift modness and setting it up as a sticky in this forum.

 
Rep Power: 510

you know what would be really helpful dezod? i am not the best at wiring schematics, so if you could get a picture of the wires from the main e-manage harness and where they connect to the ECU harness, that would help greatly. ill even toss some points your way if you can get this. thanks

 
Rep Power: 0

to be honest...........follow the schematics. A picture is even more confusing.

Time to get good at it.

This is how my E-Manage looks, and how it is staying.

 
Rep Power: 0

Updated first post.

 
Rep Power: 297

Does anyone know what harnesses come included in the Greddy turbo kit for the RSX? I belive it came with the injector harness already in the main harness. But to clear things up. can someone just tel me which harnesses theese are? (the 2 clips that clip in the side of the harness like so?)

 
Rep Power: 0

Does the main harness have half of it empty or is it all filled with wires?

 
Rep Power: 297

it's all filled with wires. would you happen to know which harnesses come with the greddy turbo kit for the rsx?

 
Rep Power: 311

I don't know if you added it or not - but it would be a wise investment to get the pressure sensor and harness with the emanage (unless you get the profec) - you can tune off of boost vs using the throttle position. Much easier and more accurate for tuning purposes.

 
Rep Power: 0

that is the injector harness...........

Once again.............the E-Manage FAQ pwnz j00 HARDCORE


The injector harness & main harness are on the same plug in harness.

 
Rep Power: 396

^^Holy crap when I do this I'm gonna burst into flames....

 
Rep Power: 0

If you can read, take your time, soldier and follow a simple wiring diagram this is a snap. People are too lazy to read through the infomation. They all want the answers spelled out to them in NEON lights. If I left out information, or someone needed clarification, I have no problem answering the Q, but when the answers are right infront of you....I am not going to anymore.

 
Rep Power: 297

so i would only install the injc. 1-4 wires and the ground right? Oh and what is the other harness that is smaller and clips next to the main one. thats the ingnition harness right? I know im not crazy but I have a felling my wire colors are a little different. Can anyone find a manuel that comes with the greddy turbo kit. I think the wires are coded a little different. and I also have this small box with a green, white, and black wires coming from it. I'll take pics tonight. I know this is coded different.

 
Rep Power: 396

I can barely read... I have ADHD, I can't soldier worth a crap (hands arn't steady enough) and following directions.. well lets just say I treid to build my legos w/o instructions first lol =)

 
Rep Power: 297

It seems the greddy website Owns me. and I found the info there.But I found something out. I don;t have some of the wires you guys have. There are no vtec wires in the main harness so I guess vtec can't be adjusted which I prob wouldn't have used anyway. But I also don't have the purple VTM wire. what does that wire do?

 
Rep Power: 0

Goes with VTEC

 
Rep Power: 297

got the main harness on but the active LED is flashing red. how do I read what code the emanage is putting out?

 
Rep Power: 0

support tool

 
Rep Power: 297

ok I have the support tool and my harness has no vtec wires connected or no VTM wire. But now my car starts to stall out and won't rev past 4k. any ideas?everything was ok till I updated the main unit,
oh BTW the active led is flashing from green to yellow to red over and over.

 
Rep Power: 510

^ mine did the same exact thing. it was because it was not tuned. you also have to reset your ECU by following the instructions in the DIY Intake page.

 
Rep Power: 510

so if we do not have vtec, we set the rotary settings to 4-8-C, correct?

 
Rep Power: 0

That is what I am using.

 
Rep Power: 396

^but you have v-tec D

 
Rep Power: 0

correct.

 
Rep Power: 297

the vtec doesn't seem to be working on our cars so everyone is using the 4-8-c.
what does it mean if the active led glows from green to yellow to red?

 
Rep Power: 0

yellow means modifing the signal and working correctly.

red means an error

This is if I recall correctly


VTEC remains untouched. No wires tapped or anything. Therefore, it still works......It engages. Diagnostics and dynos show it for me.

 
Rep Power: 297

but do you know what it means when the led flashes from green to yellow to red over and over again the whole time?