P0336 Crankshaft Position Sensor A Circut
#1
Registered!!
Thread Starter
P0336 Crankshaft Position Sensor A Circut
Hi all, today I just changed the crankshaft position sensor in my 2001 Civic because the old one went bad for some reason. When I first found the code it was P0335. Now to skip ahead that now I just replaced the sensor and put everything back together. Now the moment of truth that I start the car up and the engine stalls but I start it up again and it will run normal, It takes a couple of cranks for it to start. But just after I start and it wants to stall but then the engine continues running normally if you give it some gas. but now the code P0336 shows. When the old sensor was plugged in it would immediately stall out and never run. Plus I took it out for a test and the engine's rev limiter kicked in at around 3600 RPM. what could this be guys? I just replaced the sensor and still the problem goes on!
Kevin
Kevin
#3
If you think a good mechanic is expensive, try hiring a bad one
Re: P0336 Crankshaft Position Sensor A Circut
P0336 is CKP intermittent.
Take the connector off and look at the harness terminals. Is there any corrosion? Greenies? Corroded terminals in the old sensor?
Take the connector off and look at the harness terminals. Is there any corrosion? Greenies? Corroded terminals in the old sensor?
#4
Registered!!
Thread Starter
Re: P0336 Crankshaft Position Sensor A Circut
Hey guys sorry for the late update, No the terminals are all clean and the other day I tested the voltage of what the connector puts out and found out its putting out the correct voltage. Would you guys think is safe to drive with the "odd bucking"? I already did adjusted the timing and its still doing it! but will it be safe to drive even with the rev limiter kicking in at about 3500 RPMS?
#5
If you think a good mechanic is expensive, try hiring a bad one
Re: P0336 Crankshaft Position Sensor A Circut
Reread the OP.
OEM sensor?
Wire terminals: each has good tension when a male terminal is inserted?
OEM sensor?
Wire terminals: each has good tension when a male terminal is inserted?
#6
Re: P0336 Crankshaft Position Sensor A Circut
Hi all, today I just changed the crankshaft position sensor in my 2001 Civic because the old one went bad for some reason. When I first found the code it was P0335. Now to skip ahead that now I just replaced the sensor and put everything back together. Now the moment of truth that I start the car up and the engine stalls but I start it up again and it will run normal, It takes a couple of cranks for it to start. But just after I start and it wants to stall but then the engine continues running normally if you give it some gas. but now the code P0336 shows. When the old sensor was plugged in it would immediately stall out and never run. Plus I took it out for a test and the engine's rev limiter kicked in at around 3600 RPM. what could this be guys? I just replaced the sensor and still the problem goes on!
Kevin
Kevin
#7
Registered!!
Re: P0336 Crankshaft Position Sensor A Circut
First step usually would be to get a sensor from Honda, then use 1/4 can MAF / electrical contact cleaner on the sensor and the connector.
Inspect the “teeth” on the sprocket to make sure none snapped off.
Inspect the “teeth” on the sprocket to make sure none snapped off.
#8
d seris fan99
Join Date: May 2021
Age: 43
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: P0336 Crankshaft Position Sensor A Circut
Hi all, today I just changed the crankshaft position sensor in my 2001 Civic because the old one went bad for some reason. When I first found the code it was P0335. Now to skip ahead that now I just replaced the sensor and put everything back together. Now the moment of truth that I start the car up and the engine stalls but I start it up again and it will run normal, It takes a couple of cranks for it to start. But just after I start and it wants to stall but then the engine continues running normally if you give it some gas. but now the code P0336 shows. When the old sensor was plugged in it would immediately stall out and never run. Plus I took it out for a test and the engine's rev limiter kicked in at around 3600 RPM. what could this be guys? I just replaced the sensor and still the problem goes on!
Kevin
Kevin
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
honda.lioness
Mechanical Problems/Vehicle Issues and Fix-it Forum
4
09-17-2017 04:19 PM
AA_Sharky
Mechanical Problems/Vehicle Issues and Fix-it Forum
0
10-18-2014 02:02 PM
LividHatred
Mechanical Problems/Vehicle Issues and Fix-it Forum
3
06-18-2012 05:05 PM