How Low Should I Drop?
Thread Starter
Registered!!
Joined: May 2015
Posts: 22
Likes: 0
From: Locust Grove, GA
Rep Power: 0 
How Low Should I Drop?
Hey guys, I'm saving up the last few dollars needed before I drop my Civic. I have an '03 ES2. I'm going with Koni Yellow Struts, Ground Control Coilover sleeves, K-Sport rear camber kit, Ingallis front camber bolts & 17x7.5 Koing Torch in black (I know, I know, budgeting on wheels RN) wrapped in Nito Neogen tires (215/45/17). I hate the "big wheel, moderate drop, still looks shitty" set up that I see when most people go 17 inches. I would go 16, but I just can't find any good looking 16s within my budget. How low can/should I drop my Civic to get a nice clean stance on 17 in wheels? I was thinking 2 inches all the way around (fender roll possibly if that low?).
Also, I'll be doing the install myself, but I know I have to tow it to a shop to be aligned, so: should I put on the new suspension set up AND the front/rear camber parts, then tow it to be adjusted, or should I just install the suspension and let the shop do both the install and adjustment on the camber parts?
Thanks!
Also, I'll be doing the install myself, but I know I have to tow it to a shop to be aligned, so: should I put on the new suspension set up AND the front/rear camber parts, then tow it to be adjusted, or should I just install the suspension and let the shop do both the install and adjustment on the camber parts?
Thanks!
Re: How Low Should I Drop?
I'm dropped 2.6" front /2.4" rear. On TEIN Flex, 17x8s, +38 offset and 225/45/17s. I'm not sure if that's considered a "nice, clean stance" or not. I prefer the "meaty fitment", because I actually track my car.
I would install the rear camber arms (at maybe 3/4 of the way dialed in to ensure clearance) / drop the car / let it settle / adjust if necessary. I'd have the alignment shop install the camber bolts (unless you've done it before). Most people screw it up. Trust me on this. What's your offset? Unless you're running a really low offset (below 30s), you shouldn't have any rubbing issues, if you drive to a shop.
Good Luck.
I would install the rear camber arms (at maybe 3/4 of the way dialed in to ensure clearance) / drop the car / let it settle / adjust if necessary. I'd have the alignment shop install the camber bolts (unless you've done it before). Most people screw it up. Trust me on this. What's your offset? Unless you're running a really low offset (below 30s), you shouldn't have any rubbing issues, if you drive to a shop.
Good Luck.
Thread Starter
Registered!!
Joined: May 2015
Posts: 22
Likes: 0
From: Locust Grove, GA
Rep Power: 0 Re: How Low Should I Drop?
I'm dropped 2.6" front /2.4" rear. On TEIN Flex, 17x8s, +38 offset and 225/45/17s. I'm not sure if that's considered a "nice, clean stance" or not. I prefer the "meaty fitment", because I actually track my car.
I would install the rear camber arms (at maybe 3/4 of the way dialed in to ensure clearance) / drop the car / let it settle / adjust if necessary. I'd have the alignment shop install the camber bolts (unless you've done it before). Most people screw it up. Trust me on this. What's your offset? Unless you're running a really low offset (below 30s), you shouldn't have any rubbing issues, if you drive to a shop.
Good Luck.
I would install the rear camber arms (at maybe 3/4 of the way dialed in to ensure clearance) / drop the car / let it settle / adjust if necessary. I'd have the alignment shop install the camber bolts (unless you've done it before). Most people screw it up. Trust me on this. What's your offset? Unless you're running a really low offset (below 30s), you shouldn't have any rubbing issues, if you drive to a shop.
Good Luck.
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
alxz310
Mechanical Problems/Vehicle Issues and Fix-it Forum
10
Jul 30, 2015 12:18 PM
671civicLX
Mechanical Problems/Vehicle Issues and Fix-it Forum
1
Jul 4, 2015 04:02 PM
