Headlight Water HELPP
#1
Registered!!
Thread Starter
Join Date: Mar 2010
Location: Florida
Age: 33
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Headlight Water HELPP
I just noticed on my passenger side headlight bucket has some condensation inside. I'm 99.9% SURE it came from the rubber boot around the main headlight bulb. Its sealed up pretty good around it. I saw some water condensation on it... it doesnt completely seal around the bulb. Could i just take the bulb out and try using a hair dryer???
#2
Registered!!
Join Date: Jul 2010
Location: Earth
Posts: 61
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Headlight Water HELPP
Yes you can use a hair dryer, but there may be spots from the water left over. Are the headlights aftermarket? If so you should put some silicon adhesive around the lens, aftermarket lenses are never sealed well. The rear plug usually doesn't let water in unless it's not there or you hosed of the engine off.
#3
Administrator
Hey! Look At Me!! I'm a Supporting Member!!
Administrator
iTrader: (22)
Join Date: Aug 2003
Location: Las Vegas, NV
Age: 39
Posts: 21,456
Received 1,149 Likes
on
803 Posts
Rep Power: 485 Re: Headlight Water HELPP
pull the headlight apart, dry it out, reseal the headlight with 3m windoweld.
#5
Registered!!
Join Date: Mar 2003
Location: Austin, TX
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0
#6
Pistol grip pump in my lap at all times
Re: Headlight Water HELPP
If ya want it done right, then do what xRiceboyx says. Check his rep... You dont get that much by telling people the wrong way to do things.
#7
Administrator
Hey! Look At Me!! I'm a Supporting Member!!
Administrator
iTrader: (22)
Join Date: Aug 2003
Location: Las Vegas, NV
Age: 39
Posts: 21,456
Received 1,149 Likes
on
803 Posts
Rep Power: 485 Re: Headlight Water HELPP
I'm sure you can get away with pulling the bulbs and using a hair dryer, but unless water's been through filters and stuff, it's gonna leave residue/water spots..
Oh, and the windoweld is the stuff they use to seal windshields. It stays fairly tacky, so if you pull the headlight apart, really, all you have to do is ensure there's adequate amounts of the stuff in the channel, heat it up, and push together until it cools. I tried to find it in auto parts stores (like gearbox said) but I couldn't find it.. so I ended up buying a roll of the stuff off of amazon. I got the thick stuff (3/8") so I had to stretch it out so there wasn't a lot of excess. I found this stuff a LOT easier to deal with than RTV was to seal headlights.
I've taken my headlights apart 4-5 times, and only recently tried out the windoweld stuff this last time.
Oh, and the windoweld is the stuff they use to seal windshields. It stays fairly tacky, so if you pull the headlight apart, really, all you have to do is ensure there's adequate amounts of the stuff in the channel, heat it up, and push together until it cools. I tried to find it in auto parts stores (like gearbox said) but I couldn't find it.. so I ended up buying a roll of the stuff off of amazon. I got the thick stuff (3/8") so I had to stretch it out so there wasn't a lot of excess. I found this stuff a LOT easier to deal with than RTV was to seal headlights.
I've taken my headlights apart 4-5 times, and only recently tried out the windoweld stuff this last time.
#8
Registered!!
Join Date: Jul 2010
Location: KS
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
shaejb15
Mechanical Problems/Vehicle Issues and Fix-it Forum
2
09-03-2015 01:35 PM
MamaBear2015
7th Generation Civic 2001 - 2005
2
08-25-2015 10:47 AM
honda.lioness
7th Generation Civic 2001 - 2005
4
08-21-2015 02:36 PM