Civic Meets
Thread Starter
Ace Ventura
Joined: Mar 2005
Posts: 291
Likes: 0
Rep Power: 0 
Civic Meets
Hello I am new to the Arizona area. I am moving here from southern california for school. I just recently bought a 2005 honda civic ex coupe. I am looking to meet other people with civics, hang out, and just chill. Where do you guys usually meet? I will be in the Phoenix area. Well I hope to see some of you in the near future. Later
Subarus FTW I do NOT miss my civic
iTrader: (9)
Joined: Jul 2004
Posts: 4,595
Likes: 0
From: Scottsdale, AZ
Rep Power: 0 
Originally Posted by Rufus
lol dood your title says you have a small *****, sorry.
Dude, your title is worse. haha I like my title. I posted my sig up yesterday just to show the Feb 30th again. haha.
Joined: Jan 2003
Posts: 9,137
Likes: 1
From: Ontario
Rep Power: 379 
I think I rolled up next to him on the 101 a few times but I don't think we ever raced. I'm pretty sure I had the ported and polished head on then. If would have been fun to see how a roll on at 65 played out.
Registered!!
Joined: Aug 2004
Posts: 100
Likes: 0
From: Tempe
Rep Power: 0
Originally Posted by Tommy Tran
Hehe ya 214whp is pretty sluggish! hehe 
Peace
Peace
Originally Posted by Rufus
I've seen that SI with SLOCVIC or something on the plates. Which Si is that?
Joined: Jan 2003
Posts: 9,137
Likes: 1
From: Ontario
Rep Power: 379
Originally Posted by mdoyle
Try that minus 15whp. I doubt i'm breaking 200's yet, but probably close.
That's me (SLOW SI is the plate), if you see me on the 101, or any freeway again, start honking so that you get my attention, lol.
That's me (SLOW SI is the plate), if you see me on the 101, or any freeway again, start honking so that you get my attention, lol.
lol why so you can stomp the **** outta me?
Joined: Jan 2003
Posts: 9,137
Likes: 1
From: Ontario
Rep Power: 379 lol. **** Alex cracks me up. I think he's like Spy Hunter except for instead of dropping oil he drops ladders, t squares, rivits, dremels, routers, and drill bits. Kinda the Tim Allen of Spyhunter
LOL I can imagine that! You need to with all them damn trucks in Surprise!mdoyle I thought jdegasis said something about someone else with 214whp... and that he would have basically the same setup? Or was that an RSX guy...?
Peace
Registered!!
Joined: Aug 2004
Posts: 100
Likes: 0
From: Tempe
Rep Power: 0
Originally Posted by Tommy Tran
LOL I can imagine that! You need to with all them damn trucks in Surprise!mdoyle I thought jdegasis said something about someone else with 214whp... and that he would have basically the same setup? Or was that an RSX guy...?
Peace
I'm also pretty sure he isn't going with the custom mounts that you need for an aftermarket header to bolt up, I think he is just getting the CR-V sidemount, which I know for a fact won't allow a aftermarket header to clear the front sway (so he might be taking it off, no idea).
I really do want to run him once he gets it all done. After doin a bit more research on his swap, he will be putting down about the same horsepower as I am, but with more torque. We will both have the same tranny, but my gearing is a tad shorter due to my way smaller than stock wheels. He will rev out at 7200 while I make power till 8200.
Should be pretty good, although I have a feeling he'll pull me
Originally Posted by mdoyle
I think an RSX with the K24A2 dyno'd at that with a I/RH/E/K Pro and some turning. Degasis should be right in there, depending on if he goes and gets it tuned or not.
I'm also pretty sure he isn't going with the custom mounts that you need for an aftermarket header to bolt up, I think he is just getting the CR-V sidemount, which I know for a fact won't allow a aftermarket header to clear the front sway (so he might be taking it off, no idea).
I really do want to run him once he gets it all done. After doin a bit more research on his swap, he will be putting down about the same horsepower as I am, but with more torque. We will both have the same tranny, but my gearing is a tad shorter due to my way smaller than stock wheels. He will rev out at 7200 while I make power till 8200.
Should be pretty good, although I have a feeling he'll pull me
I'm also pretty sure he isn't going with the custom mounts that you need for an aftermarket header to bolt up, I think he is just getting the CR-V sidemount, which I know for a fact won't allow a aftermarket header to clear the front sway (so he might be taking it off, no idea).
I really do want to run him once he gets it all done. After doin a bit more research on his swap, he will be putting down about the same horsepower as I am, but with more torque. We will both have the same tranny, but my gearing is a tad shorter due to my way smaller than stock wheels. He will rev out at 7200 while I make power till 8200.
Should be pretty good, although I have a feeling he'll pull me
Peace
Registered!!
Joined: Aug 2004
Posts: 100
Likes: 0
From: Tempe
Rep Power: 0
Originally Posted by Tommy Tran
So he didnt get the 6spd tranny then??? Well if he gets kpro wont he rev out to more than 7200? Or does the head not flow enough to support 2.4l of breathing past 7200?
Peace
Peace
