dragin

iTrader: (2)

nice what did it all set ya back flaken... jk... faLKEN

FALKEN

iTrader: (55)

$145.00 shipped

dragin

iTrader: (2)

nice pm me with who ya got it throo

ponyman

iTrader: (5)

Dammit, I need a job...I wanna get my suspension done...arrrrgghhhh

dragin

iTrader: (2)

what do you wanna do to ur suspension??

ponyman

iTrader: (5)

Neuspeed Race or Sport (leaning toward sport, but don't know)
Knoi Adjustables
rear upper and lower tie bars
front lower x-brace
maybe sway bars, but most rears will bang aganst my TCS
so we are talking about 1000+ in parts
and another couple hundred to get the springs and shocks installed...the rest I will do

dragin

iTrader: (2)

if you need i know a shop that can instal it for ya... good choice on the x brace, thing is bullet proof, i naild a 2*4 a week or two ago going 50, split the board apart and didnt even chip the powder coating on the brace.. i had the sports b4 my jic's there nice but not low enough for me, nuespeeds sway/tie bar does wack my tcs from time to time... for upper id look into the cusco bar

ponyman

iTrader: (5)

^^^Thanks for the review

EVERYONE....I graduate in 7 days!!!! So, I am accepting graduation gifts. If you feel like donating pm me and I will send you my address.

Thanks

alex053

iTrader: (9)

ill send you some points

ponyman

iTrader: (5)

^^^Sweet, thanks man

FALKEN

iTrader: (55)

RobearRacing
Grey
CapYoda

FALKEN

iTrader: (55)

im looking into getting this next:

Opitma (yellow-top) battery
Neuspeed upper strut-bar (F) in black powder-coat

alex053

iTrader: (9)

dude..i can get you lightning audio or rockford batterys...same as the exide spiral cell batteries.

http://www.exideworld.com/products/a...bital_XCD.html

FALKEN

iTrader: (55)

im going to stick with the Optima...thanks though!!

FALKEN

iTrader: (55)

im thinking about messing around with the dash lights next...probably red LEDs

alex053

iTrader: (9)

i might have an optima hook up thru town and country motorsports...ill find out this weekend...

as for me, my next upgrade will be a 51" HD ready TV...4:3 but its an even trade for my 43" and has a much better picture, inputs and will display my Socom 2 in 480p w00t

FALKEN

iTrader: (55)

thanks Alex...let me know

FALKEN

iTrader: (55)

the LEDs are going to be too time consuming for what im looking to do


instead, i bought some bulb condoms from gearbox and started to install them on some of the bulbs...
its been easy so far, last night i did the Cruise Control, SunRoof, and Mirror switches

NorrinRadd

Yup, those are the easy ones. Let me know if you have any issues when you get to the cluster and center console as those two are the most difficult. You can also just check out my DIY I did a long time ago as well, good luck...

FALKEN

iTrader: (55)

thanks for the offer...i might take you up on it
(my only fear is the cluster...i dont want to kcuf it up)

NorrinRadd

Don't worry about it too much. Compared to the other areas it is harder but not too hard. The hardest part is taking the bezel (that black piece around and in front of the plastic gauge cover) around the gauge area off as it takes a lot of muscling which feels like your going to break it, don't worry just keep yanking. If you do break it (I've never heard of anyone breaking it though) it's like $8-$10 at Tempe Honda. After that, it's so easy because you just twist the bulbs in the back off and slip the cover on. Here's some tips I should have added to my DIY...

1. Instead of scratching the paint off with an exacto knife just rub paint off with 100% cotton towel and some alcohol.
2. When putting needles back on just place on at zero/plastic stop point ever so slightly that it's barely on, you don't need to go through all funky stuff others have said, this always works.

FALKEN

iTrader: (55)

NorrinRadd: how in the hell did you get the board out of the plastic for the window controls??

ive got it all torn apart but the window-lock button is holding it together still...
i cant seem to get it opened up

NorrinRadd

Be careful w/ this piece, if I remember correctly there are two or three clips you'll need to bend in order to pull up. You'll need to make sure all screws are taken out before doing this, afterwards you'll need to pull up and slowly jiggle to the point of breaking.

FALKEN

iTrader: (55)

i got it off...i just had to REALLY pull on the button

FALKEN

iTrader: (55)

i did something different from what gearbox did:

he added a whole new set-up and then ran wires...
i simply desoldered the OEM LED bulb from the board and then resoldered the new LED bulb in its place (looks OEM again)





*gearbox seems to think that mine will burn out faster than his because im using OEM products mixed with non-OEM products*

FALKEN

iTrader: (55)

i need to take my headlights apart to clean up some haze that has formed on the inside

*if anyone needs to clear/paint their headlights...let me know (Tech-Day!!)

Rufus

iTrader: (17)

My fiberglassed kickpanels are done with Diamond Audio Hex 6.5s and tweets.

FALKEN

iTrader: (55)

i changed my mind on the color of the dash lights...



im going to change the 'sedan-green' over to the 'coupe-orange'

ill be the only sedan in Arizona with coupe lighting (that im aware of)

Rufus

iTrader: (17)

I need to get Jon to sell me the rest of his exhaust. This header and downpipe need more POWER!!!!

topnotch7gen

iTrader: (22)

haha, well I might be throwin the stock piping back on so you might be able to!