Engine Post your engine related problems in this section. Engines will cover from Fuel, Engine, Cooling, Exhaust physical related items.

P1362 code keeps coming up after TDC sensor replacement.

Thread Tools
 
Search this Thread
 
Old Sep 21, 2021
  #1  
Mack27's Avatar
Thread Starter
Registered!!
 
Joined: Sep 2021
Posts: 5
Likes: 0
Rep Power: 0
Mack27 is an unknown quantity at this point
P1362 code keeps coming up after TDC sensor replacement.

Hi I’m hoping someone can help me with this. So I have a 2001 civic dx 1.7 with 186kms and about a couple months ago while driving home from work my check engine light came on and car went into “limp mode” where power was reduced. Since it was the hottest day of the summer I assumed the engine overheated and caused the sensor to fail. I shut it down for 20mins then started it up again and was able to drive home( was only a 10-15min drive from where the car gave out.) I had my friend connect his reader and it gave me the P1362 code for TDC no signal( he erased the code for me). So I went to Lordco and bought another sensor and valve cover gasket kit and replaced everything. Everything seemed fine for about a month then the same thing happened again. The engine was throwing a lot of heat when it would go into limp mode so I thought there could be an issue with the radiator or thermostat so I replaced them both. Old rad had sediment build up at bottom so it wasn’t a total waste. Car ran fine for another week then same thing happened again, driving home, power starts to surge a bit then limp mode and P1362 code pops up. Not sure what’s going on so if anyone has any ideas or has been through a similar situation id like to hear them.
Reply
Old Sep 21, 2021
  #2  
xRiCeBoYx's Avatar
Administrator
Hey! Look At Me!! I'm a Supporting Member!!
Administrator
iTrader: (22)
 
Joined: Aug 2003
Posts: 21,620
Likes: 1,252
From: Las Vegas, NV
Rep Power: 511
xRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond reputexRiCeBoYx has a reputation beyond repute
Re: P1362 code keeps coming up after TDC sensor replacement.

Was it a Honda OEM sensor or a 3rd party sensor? 3rd party sensors tend to crap out/not play nice
Reply
Old Sep 21, 2021
  #3  
Mack27's Avatar
Thread Starter
Registered!!
 
Joined: Sep 2021
Posts: 5
Likes: 0
Rep Power: 0
Mack27 is an unknown quantity at this point
Re: P1362 code keeps coming up after TDC sensor replacement.

I’m not sure if it was OEM or not. I tried to call the parts place to look back in the sale history but the guy made it seem like it was impossible. I paid about 85$ for it though. Btw I YouTube’d how to check for voltage and continuity from the sensor plug and that all seemed fine. I’m curious on what caused it to fail in the first place.
Reply
Old Sep 21, 2021
  #4  
sdaidoji's Avatar
PITA Admin
Administrator
iTrader: (1)
 
Joined: Dec 2008
Posts: 15,176
Likes: 1,605
From: TN
Rep Power: 367
sdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud ofsdaidoji has much to be proud of
Re: P1362 code keeps coming up after TDC sensor replacement.

check also wiring, they are 20 years old
there was one weird case that it turned out to be CAT.
Reply
Old Sep 21, 2021
  #5  
Mack27's Avatar
Thread Starter
Registered!!
 
Joined: Sep 2021
Posts: 5
Likes: 0
Rep Power: 0
Mack27 is an unknown quantity at this point
Re: P1362 code keeps coming up after TDC sensor replacement.

Ok I’ll give tracing the wiring a shot.
Reply
Old Sep 21, 2021
  #6  
Mack27's Avatar
Thread Starter
Registered!!
 
Joined: Sep 2021
Posts: 5
Likes: 0
Rep Power: 0
Mack27 is an unknown quantity at this point
Re: P1362 code keeps coming up after TDC sensor replacement.

Update on the replacement TDC. Found out it was an aftermarket sensor.
Reply
Old Sep 21, 2021
  #7  
FRSam's Avatar
Click Here
 
Joined: Jan 2019
Posts: 3,570
Likes: 1,349
From: Calgary, Alberta
Rep Power: 125
FRSam is a glorious beacon of lightFRSam is a glorious beacon of lightFRSam is a glorious beacon of lightFRSam is a glorious beacon of lightFRSam is a glorious beacon of lightFRSam is a glorious beacon of light
Re: P1362 code keeps coming up after TDC sensor replacement.

Originally Posted by Mack27
Update on the replacement TDC. Found out it was an aftermarket sensor.
That’s most likely your problem.
Reply
Old Sep 21, 2021
  #8  
Mack27's Avatar
Thread Starter
Registered!!
 
Joined: Sep 2021
Posts: 5
Likes: 0
Rep Power: 0
Mack27 is an unknown quantity at this point
Re: P1362 code keeps coming up after TDC sensor replacement.

Well called Honda and they had 1 TDC sensor in stock so I’ll have it in place tomorrow night. I’ll update with the results. Thanks for the input everyone!
Reply
Related Topics
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
Bobfrazier5526
Engine
18
Sep 25, 2021 07:16 PM
beernite
Engine
4
Oct 18, 2018 01:22 PM
GotU420
Engine
6
Sep 10, 2018 07:09 PM
got2run5
Mechanical Problems/Vehicle Issues and Fix-it Forum
2
Feb 2, 2012 10:30 PM
IRPancake
Mechanical Problems/Vehicle Issues and Fix-it Forum
6
Oct 8, 2009 12:21 PM




All times are GMT -5. The time now is 05:58 AM.