Parts FS EM2
Thread Starter
Registered!!
iTrader: (2)
Joined: Jan 2002
Posts: 442
Likes: 0
From: wild wild west
Rep Power: 0 
Parts FS EM2
Hi,
I got the following parts for sale.
1. OBX (revo replica) short shifter in mint condition. Bushings included.
2. Nuespeed Front upper strut bar color black in good condition.
3. 01-02 TYC Chrome projector headlamps in like new condition. eyebrows included.
Email me at Clearstraight@aol.com or AIM me at ScreenNotAvail.
Thank you
I got the following parts for sale.
1. OBX (revo replica) short shifter in mint condition. Bushings included.
2. Nuespeed Front upper strut bar color black in good condition.
3. 01-02 TYC Chrome projector headlamps in like new condition. eyebrows included.
Email me at Clearstraight@aol.com or AIM me at ScreenNotAvail.
Thank you
Thread Starter
Registered!!
iTrader: (2)
Joined: Jan 2002
Posts: 442
Likes: 0
From: wild wild west
Rep Power: 0 Hi,
The eyebrows (eternal blue color) are currently stuck to the lamps with 3M mounting tape. They can easily be removed with low heat from a hair blow dryer or heat gun without any damage to the lens. Also, when these lamps were used in the past, i have installed H1 HID setup. They have already been aimed and adjusted for HID's.
It was a painful 4-6hr job since the adjustment screws were so hard to have access.
These lamps were used for approx 6-8months before they were removed when the car was sold. All you would need is a H1 HID setup in these lamps and they are ready to be used since all adjustment has been made.
Beam Pattern when installed on my Em2:
Warmed up 8000k HID before bulbs were "broken-in"
Cold Start 8000k HID
Warmed up 8000k HID after bulbs were "broken-in" (permanent color)
Direct Shot of TYC Lamps w/ 8000k HID setup when installed on my EM2.
Current pictures of Actual TYC Lamps. HID Setup not included. All bulbs included consist of H1 low beam, H1 high beam, 194 Superwhite 5 LEDbulbs and std Signal lamp bulbs.
$80.00 FIRM and LOCAL PICK UP ONLY. Includes Original Packaging. Thank you.
Email: Clearstraight@aol.com
AIM: ScreenNotAvail
The eyebrows (eternal blue color) are currently stuck to the lamps with 3M mounting tape. They can easily be removed with low heat from a hair blow dryer or heat gun without any damage to the lens. Also, when these lamps were used in the past, i have installed H1 HID setup. They have already been aimed and adjusted for HID's.
It was a painful 4-6hr job since the adjustment screws were so hard to have access.
These lamps were used for approx 6-8months before they were removed when the car was sold. All you would need is a H1 HID setup in these lamps and they are ready to be used since all adjustment has been made.
Beam Pattern when installed on my Em2:
Warmed up 8000k HID before bulbs were "broken-in"
Cold Start 8000k HID
Warmed up 8000k HID after bulbs were "broken-in" (permanent color)
Direct Shot of TYC Lamps w/ 8000k HID setup when installed on my EM2.
Current pictures of Actual TYC Lamps. HID Setup not included. All bulbs included consist of H1 low beam, H1 high beam, 194 Superwhite 5 LEDbulbs and std Signal lamp bulbs.
$80.00 FIRM and LOCAL PICK UP ONLY. Includes Original Packaging. Thank you.
Email: Clearstraight@aol.com
AIM: ScreenNotAvail
Last edited by cvc2k2; Jan 28, 2005 at 01:36 PM.
Thread Starter
Registered!!
iTrader: (2)
Joined: Jan 2002
Posts: 442
Likes: 0
From: wild wild west
Rep Power: 0 Hi,
since there have been PM's regarding HID kits, i would suggest that you should get a complete H1 HID Kit. But if you could aquire a set of OEM ballast and plan to use them with the aftermarket rebased bulb, you will have to cut off the D2 plug and install generic adapters inorder for them to work with the H1 HID bulbs.
Here is a link for the H1 Bulbs:
http://cgi.ebay.com/ebaymotors/ws/eB...category=36476
I currently locating the link for the ballast at the moment. but please check this link to get an idea on how the modified OEM ballast looks like with aftermarket bulb plugs.
http://cgi.ebay.com/ebaymotors/ws/eB...category=36476
Thank you
since there have been PM's regarding HID kits, i would suggest that you should get a complete H1 HID Kit. But if you could aquire a set of OEM ballast and plan to use them with the aftermarket rebased bulb, you will have to cut off the D2 plug and install generic adapters inorder for them to work with the H1 HID bulbs.
Here is a link for the H1 Bulbs:
http://cgi.ebay.com/ebaymotors/ws/eB...category=36476
I currently locating the link for the ballast at the moment. but please check this link to get an idea on how the modified OEM ballast looks like with aftermarket bulb plugs.
http://cgi.ebay.com/ebaymotors/ws/eB...category=36476
Thank you
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
h4ldol
Mechanical Problems/Vehicle Issues and Fix-it Forum
1
Jun 3, 2015 03:26 PM
DouglasTheGreat
Mechanical Problems/Vehicle Issues and Fix-it Forum
2
May 27, 2015 11:23 PM
juror
Mechanical Problems/Vehicle Issues and Fix-it Forum
5
May 26, 2015 06:35 PM
