ep3 door handles
#1
Registered!!
Thread Starter
Join Date: Jun 2010
Location: Winnipeg, MB
Age: 36
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 ep3 door handles
does anyone know how to remove the outside door handles on a 2002 civic sir? i got the bolts out and the rods disconnected for the locks and door latch but it seems like something with the lock is stopping me from taking the handle off the door.
#2
Low and slow!
Join Date: Jan 2010
Location: Marion, NC
Posts: 1,628
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 190 Re: ep3 door handles
This is step by step in the service manual.
1, Remove these items:
. Door panel (see page 20-4)
. Plastic cover, as necessary( seep age 20-2)
Raise the glass fully.
Remove the lock rod protector (A).
-l Remove the screw.
-2 Release the protector from the latch protector
(B).
-3 Pull the protector down to release the hook (C)
from the door.
4. Disconnect the cylinder rod (A),and release the
retainer clip (B). then remove the lock cylinder (C).
Disconnect the outer handle rod (A).
6. Remove the maintenance cap (B),and remove the
bolts securing the outer handle( C) while holding
the handle from outside. Release the hook (D). then
remove the outer handle protector (E).
7. Pull out the outer handle (A), then remove it.
Install the handle in the reverse order of removal,
and note these items:
. Make sure each rod is connected securely.
. Make sure the door locks and opens properly.
. When installing the lock cylinder leave the outer
door handle bolts loose so the inner protector
does not interfere with the lock cylinder
installation then tighten the handle bolts.
. Install the lock cylinder retaining clip on the
handle, then install the lock cylinder. Be sure the
clip is fully seated in the slot on the lock cylinder .
. When reinstalling the door panel , make sure the
plastic cover is installed properly, and is sealed
around the covers perimeter.
1, Remove these items:
. Door panel (see page 20-4)
. Plastic cover, as necessary( seep age 20-2)
Raise the glass fully.
Remove the lock rod protector (A).
-l Remove the screw.
-2 Release the protector from the latch protector
(B).
-3 Pull the protector down to release the hook (C)
from the door.
4. Disconnect the cylinder rod (A),and release the
retainer clip (B). then remove the lock cylinder (C).
Disconnect the outer handle rod (A).
6. Remove the maintenance cap (B),and remove the
bolts securing the outer handle( C) while holding
the handle from outside. Release the hook (D). then
remove the outer handle protector (E).
7. Pull out the outer handle (A), then remove it.
Install the handle in the reverse order of removal,
and note these items:
. Make sure each rod is connected securely.
. Make sure the door locks and opens properly.
. When installing the lock cylinder leave the outer
door handle bolts loose so the inner protector
does not interfere with the lock cylinder
installation then tighten the handle bolts.
. Install the lock cylinder retaining clip on the
handle, then install the lock cylinder. Be sure the
clip is fully seated in the slot on the lock cylinder .
. When reinstalling the door panel , make sure the
plastic cover is installed properly, and is sealed
around the covers perimeter.
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
JLee93
Mechanical Problems/Vehicle Issues and Fix-it Forum
1
08-21-2015 05:44 PM
glockma630
Mechanical Problems/Vehicle Issues and Fix-it Forum
1
08-01-2015 10:30 AM
ballmich
Mechanical Problems/Vehicle Issues and Fix-it Forum
0
07-09-2015 11:59 AM