DIY: Change your Transmission Oil
#1
DIY King
Thread Starter
iTrader: (61)
Join Date: Apr 2001
Location: Shrewsbury, Massachusetts, US
Age: 47
Posts: 11,469
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 395 DIY: Change your Transmission Oil
NOTE: Pics coming soon!
Purpose of this DIY:
The Maintenence Schedule for our Civics mentions that you should replace the transmission fluid at 60,000 miles. I have heard of other people replacing their transmission fluid much sooner than that at 30,000 miles. Whichever mileage you choose, you will notice a crisper feeling to the shifter and smoother shifts after performing this DIY.
Materials needed:
- Jackstands x4
- Floor Jack
- 2 to 3 quarts of 10W-30 SAE SJ SG SH Motor Oil
- Manual Pump
- 17mm Socket
- Socket Wrench
- Oil Pan
- Plastic Container
Note on jackstands: You will need four jackstands because you will need access to the transmission filler bolt and the car must be level when checking the level of oil. Refer to Page 222 of your Civics owner's manual for more information. I happened to already have two jack stands, so I bought two more (the cheap 2-ton variety) from Walmart for $9.
Note on transmission oil: The owner's manual says that you should only use Honda's transmission oil, but it also mentions that you can use any SAE certified 10W-30 or 10W-40 grade SJ, SG, or SH motor oil as a temporary replacement. The owner manual mentions the same thing when talking about engine oil, so don't worry about using non-Honda oil.
Note on manual pump: I bought a cheapie off of HarborFreightTools.com for $10 when I was buying my manual tire changer. I also happened to spot one for $20 at Sears. My cheapie works just fine, so I suspect that the more expensive ones are a waste of money. Maybe if you're doing this 24/7, then it's a good investment, but at once every 60,000 miles you should get a cheapie.
Associated costs:
I paid about $25 for all of the materials that I needed to perform this DIY. Your expenses may be higher or lower depending upon what you already have. If you don't have any jackstands you could use concrete blocks and the stock jack to raise your car up. If you'de like to buy the cheapie jack and jackstands, then Walmart is your friend.
The socket set and socket wrench can't be replaced by a Crescent® adjustable wrench. There's simply too little room to work. If you're into tools, then you can get a very good set from HarborFreightTools.com for very little money. Compare their prices with the prices of Lowe's or Home Depot and you'll be amazed.
Instructions:
Raise the front of the car up using the floor jack. Make sure to place the jack under the front support point (pointed to by the arrow engraved in the black plastic guard underneath). Place two jack stands under the front support points (they stick out underneath on the sides behind the front wheel wells). Consult the owner's manual if in doubt as to their location.
Raise the rear of the car up using the floor jack and a short block of wood. I don't like scratching my undercarriage up and I can't elevate the car high enough by using the tow hook as a jacking point. Instead, I use a block of wood as an isolator and I place the jack in the center of the lower control arm attachment points (the metal that rear lower tie bars are attached to).
Place two jacks under the rear support points (they stick out underneath on the sides in front of the rear wheel wells). Again, consult the owner's manual if you don't know where they are. Now, here's the sneaky part... You can raise up the front of the car more than the rear to have better access to the transmission oil with the manual pump. You can also raise the rear up higher to be able to pump in more of the transmission oil. I did neither when I performed this DIY; it's just something that came to mind when I was done.
Locate the transmission oil filler bolt. Refer to page nr. 222 of the owner's manual for a picture of it's location. You'll need good lighting when you're working under your car, or else you'll come out from under there covered in oil and you won't even know it. At the very least, position a flashlight to direct light at the filler bolt. If you need an excuse to buy another tool, then I suggest that you get one of those hanging lights that uses regular light bulbs.
Place the oil pan under the transmission oil filler bolt hole and use the 17mm socket and socket wrench to loosen it. Unscrew it the rest of the way by hand and be ready for some oil to flow out (more or less, depending on how you adjusted your jack stands). Assemble the manual pump according to its instructions. Mine came with an adapter for a smaller diameter hose and the hose itself, which I used to put into the transmission housing. The larger diameter hose also fit, but not all the way in.
Feel around with the hose inside of the transmission housing to reach the lowest spot possible. Make sure that the hose does not move; I simply wedged it in there and it stayed put. Then begin pumping out the old transmission oil into any plastic container with a large capacity and a narrow neck (like a used milk container), or else you'll cover everything in oil as it tends to not flow smoothly. Instead, it gushes out in waves and can make quite a mess if you try to catch it in the oil pan. The oil pan is just there to catch any oil coming out of the transmission oil filler bolt hole.
After you pump out all of the old transmission oil, you will need to pump in the new transmission oil. To do this you will need to reverse the hoses on the pump, so that the oil is pumped into the transmission housing through the smaller diameter hose. I was able to pump in more than two full quarts of oil, although I did end up wasting a little in the process. You should stop pumping when the oil starts to leak out from the transmission oil filler bolt hole.
At this point I put the transmission oil filler bolt back into place and torqued it down conservatively (25 - 35 foot pounds). It's not load bearing and has a crush washer that should act as a spring to keep the bolt from vibrating out. I then lowered the car and cleaned up everything that was covered in oil. If you're wondering what to do with the old oil... Simply return it to the place where you bought your new oil. For me that was Walmart; they should take it back from you without question. Most states have laws that require the people who sell oil to take back used oil and then dispose of it properly.
The very last part of this DIY requires that you do everyting over again after driving around for a while. I did and I was able to fill up the transmission housing with even more oil. Maybe it was the air bubbles that had to settle out of the oil? Maybe it was the recesses that I couldn't get to the first time? Maybe the oil was thrown into the recesses that I couldn't get to under cornering forces? Who knows how it happened, the fact is that I was able to put in another half a pint of oil.
Driving Impressions:
I did this DIY about 2,500 miles ago and I think it's worth it. I can "feel" the gears through the shifter much better than before. Shifting is "crisper" than ever and 2nd doesn't pop out on me as much as it used to. As a side-story, the 2nd gear poppping out problem is on certain 2001 Civics and is covered under warranty, but I didn't get it fixed before my warranty expired. Oh well, I can live with it. Especially since my plan is to get a K24/K20A2 frankenstein motor into my car later on down the road.
Purpose of this DIY:
The Maintenence Schedule for our Civics mentions that you should replace the transmission fluid at 60,000 miles. I have heard of other people replacing their transmission fluid much sooner than that at 30,000 miles. Whichever mileage you choose, you will notice a crisper feeling to the shifter and smoother shifts after performing this DIY.
Materials needed:
- Jackstands x4
- Floor Jack
- 2 to 3 quarts of 10W-30 SAE SJ SG SH Motor Oil
- Manual Pump
- 17mm Socket
- Socket Wrench
- Oil Pan
- Plastic Container
Note on jackstands: You will need four jackstands because you will need access to the transmission filler bolt and the car must be level when checking the level of oil. Refer to Page 222 of your Civics owner's manual for more information. I happened to already have two jack stands, so I bought two more (the cheap 2-ton variety) from Walmart for $9.
Note on transmission oil: The owner's manual says that you should only use Honda's transmission oil, but it also mentions that you can use any SAE certified 10W-30 or 10W-40 grade SJ, SG, or SH motor oil as a temporary replacement. The owner manual mentions the same thing when talking about engine oil, so don't worry about using non-Honda oil.
Note on manual pump: I bought a cheapie off of HarborFreightTools.com for $10 when I was buying my manual tire changer. I also happened to spot one for $20 at Sears. My cheapie works just fine, so I suspect that the more expensive ones are a waste of money. Maybe if you're doing this 24/7, then it's a good investment, but at once every 60,000 miles you should get a cheapie.
Associated costs:
I paid about $25 for all of the materials that I needed to perform this DIY. Your expenses may be higher or lower depending upon what you already have. If you don't have any jackstands you could use concrete blocks and the stock jack to raise your car up. If you'de like to buy the cheapie jack and jackstands, then Walmart is your friend.
The socket set and socket wrench can't be replaced by a Crescent® adjustable wrench. There's simply too little room to work. If you're into tools, then you can get a very good set from HarborFreightTools.com for very little money. Compare their prices with the prices of Lowe's or Home Depot and you'll be amazed.
Instructions:
Raise the front of the car up using the floor jack. Make sure to place the jack under the front support point (pointed to by the arrow engraved in the black plastic guard underneath). Place two jack stands under the front support points (they stick out underneath on the sides behind the front wheel wells). Consult the owner's manual if in doubt as to their location.
Raise the rear of the car up using the floor jack and a short block of wood. I don't like scratching my undercarriage up and I can't elevate the car high enough by using the tow hook as a jacking point. Instead, I use a block of wood as an isolator and I place the jack in the center of the lower control arm attachment points (the metal that rear lower tie bars are attached to).
Place two jacks under the rear support points (they stick out underneath on the sides in front of the rear wheel wells). Again, consult the owner's manual if you don't know where they are. Now, here's the sneaky part... You can raise up the front of the car more than the rear to have better access to the transmission oil with the manual pump. You can also raise the rear up higher to be able to pump in more of the transmission oil. I did neither when I performed this DIY; it's just something that came to mind when I was done.
Locate the transmission oil filler bolt. Refer to page nr. 222 of the owner's manual for a picture of it's location. You'll need good lighting when you're working under your car, or else you'll come out from under there covered in oil and you won't even know it. At the very least, position a flashlight to direct light at the filler bolt. If you need an excuse to buy another tool, then I suggest that you get one of those hanging lights that uses regular light bulbs.
Place the oil pan under the transmission oil filler bolt hole and use the 17mm socket and socket wrench to loosen it. Unscrew it the rest of the way by hand and be ready for some oil to flow out (more or less, depending on how you adjusted your jack stands). Assemble the manual pump according to its instructions. Mine came with an adapter for a smaller diameter hose and the hose itself, which I used to put into the transmission housing. The larger diameter hose also fit, but not all the way in.
Feel around with the hose inside of the transmission housing to reach the lowest spot possible. Make sure that the hose does not move; I simply wedged it in there and it stayed put. Then begin pumping out the old transmission oil into any plastic container with a large capacity and a narrow neck (like a used milk container), or else you'll cover everything in oil as it tends to not flow smoothly. Instead, it gushes out in waves and can make quite a mess if you try to catch it in the oil pan. The oil pan is just there to catch any oil coming out of the transmission oil filler bolt hole.
After you pump out all of the old transmission oil, you will need to pump in the new transmission oil. To do this you will need to reverse the hoses on the pump, so that the oil is pumped into the transmission housing through the smaller diameter hose. I was able to pump in more than two full quarts of oil, although I did end up wasting a little in the process. You should stop pumping when the oil starts to leak out from the transmission oil filler bolt hole.
At this point I put the transmission oil filler bolt back into place and torqued it down conservatively (25 - 35 foot pounds). It's not load bearing and has a crush washer that should act as a spring to keep the bolt from vibrating out. I then lowered the car and cleaned up everything that was covered in oil. If you're wondering what to do with the old oil... Simply return it to the place where you bought your new oil. For me that was Walmart; they should take it back from you without question. Most states have laws that require the people who sell oil to take back used oil and then dispose of it properly.
The very last part of this DIY requires that you do everyting over again after driving around for a while. I did and I was able to fill up the transmission housing with even more oil. Maybe it was the air bubbles that had to settle out of the oil? Maybe it was the recesses that I couldn't get to the first time? Maybe the oil was thrown into the recesses that I couldn't get to under cornering forces? Who knows how it happened, the fact is that I was able to put in another half a pint of oil.
Driving Impressions:
I did this DIY about 2,500 miles ago and I think it's worth it. I can "feel" the gears through the shifter much better than before. Shifting is "crisper" than ever and 2nd doesn't pop out on me as much as it used to. As a side-story, the 2nd gear poppping out problem is on certain 2001 Civics and is covered under warranty, but I didn't get it fixed before my warranty expired. Oh well, I can live with it. Especially since my plan is to get a K24/K20A2 frankenstein motor into my car later on down the road.
#2
id try to stick to honda mtf insted of motor oil. its not very expensive. the way i see it, even if you change your fluid only once a year, say every 12-15k, which is drastically below the recommended interval, youd only be spending around $8 per year on fluid, vs $2-3 for motor oil. i bet i could find the $5-6 dollar difference in change around my house
#3
Registered!!
iTrader: (13)
Join Date: Apr 2003
Location: Miami (Pembroke Pines), Florida
Age: 41
Posts: 17,176
Likes: 0
Received 3 Likes
on
3 Posts
Rep Power: 429 you might wanna note that this is a DIY for Manual trannsmissions, auto transmission fluid change uses different fluid and the process is a bit different with different tools.
#4
I need TP for my bunghole
iTrader: (3)
Join Date: Jan 2003
Location: OXNARD, CA. SoCal. "805", North of L.A.
Age: 46
Posts: 7,103
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 336 good DIY..
I love www.HarborFreight.com.
I live close to one.
I can spend hours in that store buying stuff.
I love www.HarborFreight.com.
I live close to one.
I can spend hours in that store buying stuff.
#6
Registered!!
iTrader: (4)
Join Date: Aug 2004
Posts: 1,619
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 257 anything honda recommends multiply it by 1.5 imo
I had my tranny repalced at 40,0000 and am now at 101,000 (km) and my mechanic said i dont need a tranny fluid change, at least I know my mechanics honest, I went to one of those quick lube places, and they told me to drain my tranny fluid 15k after i got the new tranny installed. I told them they should be ashamed of themselves
I had my tranny repalced at 40,0000 and am now at 101,000 (km) and my mechanic said i dont need a tranny fluid change, at least I know my mechanics honest, I went to one of those quick lube places, and they told me to drain my tranny fluid 15k after i got the new tranny installed. I told them they should be ashamed of themselves
#7
Registered!!
Join Date: Jun 2004
Location: Brampton, On
Age: 41
Posts: 373
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 You don't need the pump... there is a drain at the bottom of the housing that you can remove using only a ratchet (without a socket on it). To fill I used a tube and funnel.
#8
Registered!!
iTrader: (13)
Join Date: Apr 2003
Location: Miami (Pembroke Pines), Florida
Age: 41
Posts: 17,176
Likes: 0
Received 3 Likes
on
3 Posts
Rep Power: 429
Originally Posted by AggressiveAdam
anything honda recommends multiply it by 1.5 imo
I had my tranny repalced at 40,0000 and am now at 101,000 (km) and my mechanic said i dont need a tranny fluid change, at least I know my mechanics honest, I went to one of those quick lube places, and they told me to drain my tranny fluid 15k after i got the new tranny installed. I told them they should be ashamed of themselves
I had my tranny repalced at 40,0000 and am now at 101,000 (km) and my mechanic said i dont need a tranny fluid change, at least I know my mechanics honest, I went to one of those quick lube places, and they told me to drain my tranny fluid 15k after i got the new tranny installed. I told them they should be ashamed of themselves
#9
iTrader: (11)
Join Date: Feb 2004
Location: Miami
Age: 41
Posts: 2,784
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 274
Originally Posted by 7Gnoob
You don't need the pump... there is a drain at the bottom of the housing that you can remove using only a ratchet (without a socket on it). To fill I used a tube and funnel.
#11
Registered!!
Join Date: Apr 2002
Location: Rockville, Maryland
Posts: 305
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 0
Originally Posted by 7Gnoob
You don't need the pump... there is a drain at the bottom of the housing that you can remove using only a ratchet (without a socket on it). To fill I used a tube and funnel.
#14
Registered!!
Join Date: Apr 2002
Location: Rockville, Maryland
Posts: 305
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 0
Originally Posted by _Viper_
Man where does all that mud come from??
Are you using the Vic as a 4X4 lolll
Are you using the Vic as a 4X4 lolll
Last edited by Storm897; 05-20-2008 at 01:12 PM.
#16
DIY King
Thread Starter
iTrader: (61)
Join Date: Apr 2001
Location: Shrewsbury, Massachusetts, US
Age: 47
Posts: 11,469
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 395
Originally Posted by Storm897
I agree. Theres two bolts in the Transmission Case. Bolt #1 and Bolt #2 in the Picture Below. First take a 3/8 inch socket wrench and remove bolt #2 to remove the MTF (Manual transmission Fluid). Then after the MTF has been removed, screw in bolt #2 to spec and remove bolt #1 (Using a 17mm Socket) to place back MTF back in to the transmission.
#17
Jeremy's Iron
Join Date: May 2002
Location: Baytown, Texas, US
Age: 42
Posts: 1,469
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 I had actually seen both bolts on the transmission, too, but the manual only tells you so much. I didn't want to drain it without buying a funnel first. I was wondering why you were using the pump, Grey...
#19
Why is my vagina bleeding?
iTrader: (1)
Join Date: Mar 2004
Location: Montreal
Age: 44
Posts: 3,582
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 281 ^^^^^^ You need to change it but not as often as a auto, check your manual if you don't believe me. Changing your tranny fluid insn't expensive and its not hard, I thikn its good to be precautious.
#22
Bone Stock!
Join Date: Oct 2003
Location: Rowland Heights, CA
Age: 40
Posts: 1,879
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 10W-30 Motor oil in the transmission? I thought all transmission oil are red and they are ATF+ and Dexron. Maybe i am missing something.
Last edited by dalaw; 07-14-2005 at 12:33 AM.
#23
Registered!!
iTrader: (6)
Join Date: Aug 2001
Location: Sycamore, Illinois, US
Age: 46
Posts: 1,351
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 I just want to add that I recently had a problem with a mechanic putting 10w30 motor oil in my tranny when I had my clutch installed. I had nothing but problems, gridning syncros, mis-shifts, popping out of gear. I went back and made him put in HOnda MTF, and now it works like it should, no more gridning gears! ONLY USE HONDA MTF!!!
#24
Touch it... He won't bite, He'll just come at you pretty quick.
Join Date: Apr 2005
Location: Wilkes-Barre, Pa
Age: 39
Posts: 1,278
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0
Originally Posted by IDQcivic
I just want to add that I recently had a problem with a mechanic putting 10w30 motor oil in my tranny when I had my clutch installed. I had nothing but problems, gridning syncros, mis-shifts, popping out of gear. I went back and made him put in HOnda MTF, and now it works like it should, no more gridning gears! ONLY USE HONDA MTF!!!
#25
<---- I am really this short in person!
Join Date: Oct 2004
Location: illinois
Age: 43
Posts: 647
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 I need a DIY for an auto!!!!!!
go under the car and remove the tranny bolt. it is a bolt that a 3/8 ratchet head will fit into, dont need a socket. Remove that, drain the tranny fluid, put back on, then add 3 quarts at the tranny dipstick in the engine compartment.
go under the car and remove the tranny bolt. it is a bolt that a 3/8 ratchet head will fit into, dont need a socket. Remove that, drain the tranny fluid, put back on, then add 3 quarts at the tranny dipstick in the engine compartment.
Last edited by streetglower; 09-01-2005 at 01:42 PM.
#26
Registered!!
iTrader: (1)
Join Date: Jul 2003
Location: Southern Utah
Age: 39
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0
Originally Posted by IDQcivic
I just want to add that I recently had a problem with a mechanic putting 10w30 motor oil in my tranny when I had my clutch installed. I had nothing but problems, gridning syncros, mis-shifts, popping out of gear. I went back and made him put in HOnda MTF, and now it works like it should, no more gridning gears! ONLY USE HONDA MTF!!!
You are up in the night bro. I change my fluid every year with Mobil 1 10w-30 Synthetic! I have never had any problems at all! Honda always says to use their brand of oil and MTf because they want to make more money! Think about it.
So just so everybody knows, use 10w-30 Mobil 1 Synthetic or any other 10w-30 motor oil.
#28
Registered!!
iTrader: (13)
Join Date: Apr 2003
Location: Miami (Pembroke Pines), Florida
Age: 41
Posts: 17,176
Likes: 0
Received 3 Likes
on
3 Posts
Rep Power: 429
Originally Posted by BSonly
Honda mechanic(friend) gave me 4 quarts of ATF. I've heard to use 2 or 3 or 4 quarts??? so what is it? do i fill it up until it spills out?
#29
Registered!!
Join Date: Aug 2005
Location: Raleigh, NC
Age: 46
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0
Originally Posted by Storm897
I agree. Theres two bolts in the Transmission Case. Bolt #1 and Bolt #2 in the Picture Below. First take a 3/8 inch socket wrench and remove bolt #2 to remove the MTF (Manual transmission Fluid). Then after the MTF has been removed, screw in bolt #2 to spec and remove bolt #1 (Using a 17mm Socket) to place back MTF back in to the transmission.
#30
Registered!!
Join Date: Apr 2002
Location: Rockville, Maryland
Posts: 305
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 0
Originally Posted by grapehead
for future reference, always remove the fill bolt before the drain bolt. on vehicles where rust/mud/etc make removing bolts an issue, the home wrench could get into a situation where he has emptied the tranny with no way to refill it.
Thanks