Honda Civic Forum
0 2019/03/01 08:58:17
0 2019/02/28 09:30:58
0 2019/02/28 09:30:54
0 2019/02/28 09:30:50
0 2019/02/28 09:30:44
0 2019/02/22 07:43:03
almost gotter round
almost gotter round
0 2019/02/22 07:42:58
0 2019/02/22 07:06:36
0 2019/02/22 07:06:29
70MM TB now fits.
70MM TB now fits.
0 2019/02/21 09:09:28
0 2019/02/21 09:09:22
Made a Flange and had it Tig welded on
Made a Flange and had it Tig welded on
0 2019/02/21 09:09:17
Had to Bore out the intake hole
Had to Bore out the intake hole
0 2019/02/21 09:09:11
0 2019/02/21 09:07:49
now the 70mm TB fits!
now the 70mm TB fits!
0 2019/02/21 09:07:16
Tig welded a new TB adapter
Tig welded a new TB adapter
0 2019/02/21 09:07:11
Cut the flange and bored out the intake hole
Cut the flange and bored out the intake hole
0 2019/02/21 09:07:05
Slowly cutting this on the lathe...
Slowly cutting this on the lathe...
0 2019/02/21 08:53:39
Throttle Body Installed
Throttle Body Installed
0 2019/02/18 09:21:16
Ground some of the welds
Ground some of the welds
0 2019/02/18 09:21:10
Repainted
Repainted
0 2019/02/18 09:21:04
back at it. Going to make a round piece from some left over square stock...
back at it. Going to make a round piece from some left over square stock...
0 2019/02/15 11:47:19
Used jb weld for the outside and as it was drying, i sprinkled grindings on the jb weld. My theory is it will help strengthen the bond but also makes it look nicer...
Used jb weld for the outside and as it was drying, i sprinkled grindings on the jb weld. My theory is it will help strengthen the bond but also makes it look nicer...
0 2019/02/14 07:09:23
Not enough space to tig the whole outside so we did the whole inside and about 1/2 of the outside.
Not enough space to tig the whole outside so we did the whole inside and about 1/2 of the outside.
0 2019/02/14 07:09:17
Hand placement is about as close as it's gonna get. Time for the tig!
Hand placement is about as close as it's gonna get. Time for the tig!
0 2019/02/12 06:27:36
I cut that little tab off
I cut that little tab off
0 2019/02/12 06:27:30
0 2019/02/12 06:27:25
0 2018/12/07 12:23:12
d16 lsd. the two gears shown needed to be milled down a bit
d16 lsd. the two gears shown needed to be milled down a bit
0 2018/11/09 07:57:53
0 2018/10/12 07:57:22
Turbo, and radiator all attached...but upper radiator mount is cut. I have hood pins holding hood down.
Turbo, and radiator all attached...but upper radiator mount is cut. I have hood pins holding hood down.
0 2018/10/09 07:07:38
0 2018/10/05 07:12:04
0 2018/10/05 07:12:03
hurst
hurst
0 2018/09/21 13:34:15
0 2018/09/21 13:33:30
0 2018/09/21 13:32:47
0 2018/09/21 13:32:18
0 2018/09/21 13:31:27
Final plate. The angled cut is necessary to clear the shifter boot cover. Bottom two holes for mounting. I drilled two holes to try different throw angles. Utilizing the top hole brings the throw down to 2.75 inches.
Final plate. The angled cut is necessary to clear the shifter boot cover. Bottom two holes for mounting. I drilled two holes to try different throw angles. Utilizing the top hole brings the throw down to 2.75 inches.
0 2018/09/21 11:19:03
0 2018/09/21 11:19:03