Honda Civic Forum
0 2018/10/12 07:57:22
d16 lsd. the two gears shown needed to be milled down a bit
d16 lsd. the two gears shown needed to be milled down a bit
0 2018/11/09 07:57:53
0 2018/12/07 12:23:12
0 2019/02/12 06:27:25
I cut that little tab off
I cut that little tab off
0 2019/02/12 06:27:30
Hand placement is about as close as it's gonna get. Time for the tig!
Hand placement is about as close as it's gonna get. Time for the tig!
0 2019/02/12 06:27:36
Not enough space to tig the whole outside so we did the whole inside and about 1/2 of the outside.
Not enough space to tig the whole outside so we did the whole inside and about 1/2 of the outside.
0 2019/02/14 07:09:17
Used jb weld for the outside and as it was drying, i sprinkled grindings on the jb weld. My theory is it will help strengthen the bond but also makes it look nicer...
Used jb weld for the outside and as it was drying, i sprinkled grindings on the jb weld. My theory is it will help strengthen the bond but also makes it look nicer...
0 2019/02/14 07:09:23
back at it. Going to make a round piece from some left over square stock...
back at it. Going to make a round piece from some left over square stock...
0 2019/02/15 11:47:19
Repainted
Repainted
0 2019/02/18 09:21:04
Ground some of the welds
Ground some of the welds
0 2019/02/18 09:21:10
Throttle Body Installed
Throttle Body Installed
0 2019/02/18 09:21:16
Slowly cutting this on the lathe...
Slowly cutting this on the lathe...
0 2019/02/21 08:53:39
Cut the flange and bored out the intake hole
Cut the flange and bored out the intake hole
0 2019/02/21 09:07:05
Tig welded a new TB adapter
Tig welded a new TB adapter
0 2019/02/21 09:07:11
now the 70mm TB fits!
now the 70mm TB fits!
0 2019/02/21 09:07:16
0 2019/02/21 09:07:49
Had to Bore out the intake hole
Had to Bore out the intake hole
0 2019/02/21 09:09:11
Made a Flange and had it Tig welded on
Made a Flange and had it Tig welded on
0 2019/02/21 09:09:17
0 2019/02/21 09:09:22
70MM TB now fits.
70MM TB now fits.
0 2019/02/21 09:09:28
0 2019/02/22 07:06:29
0 2019/02/22 07:06:36
almost gotter round
almost gotter round
0 2019/02/22 07:42:58
0 2019/02/22 07:43:03
0 2019/02/28 09:30:44
0 2019/02/28 09:30:50
0 2019/02/28 09:30:54
0 2019/02/28 09:30:58
0 2019/03/01 08:58:17
0 2019/03/01 08:58:22
0 2019/03/01 08:58:27
0 2019/03/01 08:58:33
0 2019/03/01 08:59:25
0 2019/03/01 09:00:22
shifter tab welded on and extended.
shifter tab welded on and extended.
0 2019/03/04 06:46:28
slowly cutting the outer edge off...
slowly cutting the outer edge off...
0 2019/03/14 12:50:16
Night two of rough cut
Night two of rough cut
0 2019/03/15 07:08:22
0 2019/03/19 14:51:05
The red one is for a cheap ebay d16 cam gear that doesn't fit the D17 AEM cam gear.
The red one is for a cheap ebay d16 cam gear that doesn't fit the D17 AEM cam gear.
0 2019/03/20 14:01:41