Gonzo.
#3091
Re: Page 200 = New Video! - Page 200 - The Speedfoos' Turbo Thread!!
1.5" steel conduit and a racheting tie down strap.
LOL, this wouldn't happen to be the 1.5" that lowes gave you like 100 pages back, which was the wrong stuff was it?
#3092
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = New Video! - Page 200 - The Speedfoos' Turbo Thread!!
Glad you like it.
Aside from the little EG hatches and EP3s, EM2s are probably my favorite Honda chassis.
LOL - same stuff! Wasn't the wrong thing, just didn't need 10' of it for the dump tube I made.
LOL - same stuff! Wasn't the wrong thing, just didn't need 10' of it for the dump tube I made.
#3094
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = New Video! - Page 200 - The Speedfoos' Turbo Thread!!
Piston rings and my hood strut brackets arrived today! Woot!
But I have to paint a valve cover before I can mess with the rings.....grrr.
I'm painting a base coat on the cover for my mother-in-law to work from. She's going to do a little airbrushing on it, I can't wait. And it's done!
Bottom end is together now so it's just a matter of time before I shoehorn the motor back in. This will be the last stock bore rebuild on this block though. My rings barely needed to be gapped. Next rebuild will have to bored .020 over.
But anyway, pictures pictures.
Installed the pistons....
Torqued down the girdle and the rods, installed the oil pickup and dipstick guide...
And capped her off with the oil pan. Job done!
But I have to paint a valve cover before I can mess with the rings.....grrr.
I'm painting a base coat on the cover for my mother-in-law to work from. She's going to do a little airbrushing on it, I can't wait. And it's done!
Bottom end is together now so it's just a matter of time before I shoehorn the motor back in. This will be the last stock bore rebuild on this block though. My rings barely needed to be gapped. Next rebuild will have to bored .020 over.
But anyway, pictures pictures.
Installed the pistons....
Torqued down the girdle and the rods, installed the oil pickup and dipstick guide...
And capped her off with the oil pan. Job done!
#3095
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = New Video! - Page 200 - The Speedfoos' Turbo Thread!!
Buh bye.
Last edited by speedfoos; 12-10-2009 at 10:26 AM.
#3097
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Thanks Scott! How are things at merry old Molesworth? Any plans to PCS back to the states? Galloway is still pimpin' the "V". He goes back and forth on a near daily basis about selling it, GSR swapping it (he already has the head and block) turboing it, or SCing it. It's almost comical.
#3098
Registered!!
iTrader: (3)
Join Date: Mar 2004
Location: FL
Posts: 1,647
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 262 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
England is ok, the dollar to pound exchange rate went down, so that helps with travel. However, I'm sick of my job. Being in an office for most of the day drives me crazy, but I am enjoying the slow ops tempo. Nikki and I are planning to PSC back to the states in January. We prefer something in the lower east coast, but we also wouldn't mind going to somewhere in the mid-west. As long as we get a place that has a good mission, location and a place for Nikki to work, I'll be happy.
What's holding back Galloway from committing on the engine swap?
How's North Carolina treating you?
What's holding back Galloway from committing on the engine swap?
How's North Carolina treating you?
#3099
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Buh bye.
Last edited by speedfoos; 12-10-2009 at 10:26 AM.
#3100
Registered!!
iTrader: (4)
Join Date: Feb 2007
Age: 41
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 210 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
This might be a noob question or maybe I just missed something in another post but, what are the extended studs for?
#3101
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Honestly, not a whole lot. NHRA rules state that cars running a set time or below (can't remember) have to run extended, open bolt studs that the officials can quickly ensure that the studs aren't broken. I don't think my car will ever run that fast, but they were free so I put them on.
#3102
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Buh bye.
Last edited by speedfoos; 12-10-2009 at 10:27 AM.
#3103
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Buh bye.
Last edited by speedfoos; 12-10-2009 at 10:27 AM.
#3104
Registered!!
iTrader: (6)
Join Date: May 2006
Location: North Brunswick, New Jersey
Age: 41
Posts: 1,713
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 257 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Good luck Clint, she looks better than ever. Job well done. I just hope it runs as good as it looks.
#3106
Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
very nice clint. your a beast. i would never gather up enough motivation to work on my car for like a week straight. i HATE repairing/diagnosing cars, but i love modding them.
and why is it that the last page of your thread never works? it says there are 208 pages but i can only go up to 207. lol
and why is it that the last page of your thread never works? it says there are 208 pages but i can only go up to 207. lol
#3107
Registered!!
Join Date: May 2008
Age: 36
Posts: 107
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
quick question what radiator is that that your running. Is it for the ek body style civics. it almost looks like the one my brother bought for his 96 ek.
#3108
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
It is for the EKs.
But I can't get it running and I give up. Part out thread in the FS section.
But I can't get it running and I give up. Part out thread in the FS section.
#3109
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Double-post FTL.
Last edited by speedfoos; 02-17-2009 at 08:00 AM.
#3110
A long winded 7th genr
Join Date: Jan 2006
Location: Northern California Humboldt
Posts: 1,755
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 263 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Great stuff dude. Always inspirational. So lets see.... you've probably rebuilt your engine more this past year then some people do in their lifetime! Well, I wouldn't be surprised if it was true.
I love that lighting airbrush. Different.
Keep up the good work, can't wait to see it when it's done. Cinematic sequences, aka videoz ftw.
I love that lighting airbrush. Different.
Keep up the good work, can't wait to see it when it's done. Cinematic sequences, aka videoz ftw.
#3111
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
Great stuff dude. Always inspirational. So lets see.... you've probably rebuilt your engine more this past year then some people do in their lifetime! Well, I wouldn't be surprised if it was true.
I love that lighting airbrush. Different.
Keep up the good work, can't wait to see it when it's done. Cinematic sequences, aka videoz ftw.
I love that lighting airbrush. Different.
Keep up the good work, can't wait to see it when it's done. Cinematic sequences, aka videoz ftw.
#3114
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
LOL - I'll be around for a while yet. This part-out isn't going to happen overnight!
#3117
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
A lot of the little stuff is gone, some big stuff, but I'm sure I'll have to look elsewhere to move the turbo, possibly the block and IM too.
#3120
My Pony Princess is the inspiration for my ride.
Thread Starter
iTrader: (17)
Join Date: Apr 2006
Age: 48
Posts: 5,217
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: Page 200 = Almost done - Again -The Speedfoos' Turbo Thread!! Post #3095
She's getting completely parted out, everything being sold and then I'm going to cut up the carcass with a sawzall and sell it for scrap.