P1259 vtec really sucks
#1
Registered!!
Thread Starter
Join Date: Oct 2017
Age: 50
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 P1259 vtec really sucks
I got fresh oil, switched 2 solenoids and 2 vtec oil sensors and 2 vtec housings... still get p1259... only other thing could be fuel pressure? So either the fuel pressure regulator or fuel pump could have low pressure?... the vtec wire is cut and twisted on the harness side.
Last edited by 310civicEX; 09-25-2018 at 05:02 PM.
#4
If you think a good mechanic is expensive, try hiring a bad one
Re: P1259 vtec really sucks
only other thing could be fuel pressure? So either the fuel pressure regulator or fuel pump could have low pressure?
Fuel problems would give you very different symptoms and codes.
#5
PITA Admin
Administrator
iTrader: (1)
Join Date: Dec 2008
Location: TN
Age: 52
Posts: 14,779
Received 1,440 Likes
on
1,196 Posts
Rep Power: 338 Re: P1259 vtec really sucks
cheap one... fix properly the wiring. go from there
#6
Registered!!
Thread Starter
Join Date: Oct 2017
Age: 50
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0
#8
Registered!!
Re: P1259 vtec really sucks
This is completely different circuit than the low level oil sender.
Honda engineers are pretty smart and I have no doubt they also built in other safety features.
#9
If you think a good mechanic is expensive, try hiring a bad one
Re: P1259 vtec really sucks
But is it?
There are many different possible causes for the vtec code.
Do you understand how the valve is suoopsed to work, and what the computer has to see in order to stay happy?
Got FF data? What rpm was it when the code set?
What all work has heen done to your engine recrntly, again? Refresh my memory.
#10
Registered!!
Thread Starter
Join Date: Oct 2017
Age: 50
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: P1259 vtec really sucks
That should read "could be low OIL pressure".
But is it?
There are many different possible causes for the vtec code.
Do you understand how the valve is suoopsed to work, and what the computer has to see in order to stay happy?
Got FF data? What rpm was it when the code set?
What all work has heen done to your engine recrntly, again? Refresh my memory.
But is it?
There are many different possible causes for the vtec code.
Do you understand how the valve is suoopsed to work, and what the computer has to see in order to stay happy?
Got FF data? What rpm was it when the code set?
What all work has heen done to your engine recrntly, again? Refresh my memory.
#11
If you think a good mechanic is expensive, try hiring a bad one
Re: P1259 vtec really sucks
I want to know what the RPM was when the fault code set . THAT is what Freeze Frame data is for.
If you have live data, does it show VTEC on/off?
Does it also show the vtec pressure switch on/off?
#12
Registered!!
Thread Starter
Join Date: Oct 2017
Age: 50
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: P1259 vtec really sucks
I got it all together. .is there a way to check if it's good? I reved it up to 5500 rpm and the light never came on.
#13
If you think a good mechanic is expensive, try hiring a bad one
Re: P1259 vtec really sucks
I might assume it must have set the code at high rpm when vtec would have been activated?
I have used test lights and voltmeters to monitor the vtec command and response .
Did you have the cylinder head off this engine just before the vtec code came up?
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
alkb1666a2
6th Generation Civic 1996 - 2000
3
02-20-2010 08:45 PM
2k2civicballer
Parts and Products
14
04-06-2002 11:36 PM