What kind of glue to bond EX coupe's tweeter pods to new tweeters?
#1
Registered!!
Thread Starter
Join Date: Apr 2011
Location: Seattle, WA
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 What kind of glue to bond EX coupe's tweeter pods to new tweeters?
I'm in the midst of installing a set of Rockford Fosgate components in the front doors/tweeter pods of my 2002 EX coupe and have come to the part where I need to glue (permanently) the stock tweeter pods (from which I removed the stock tweeter from) to my new tweeters. I tried superglue but it wasn't sticking. I have PVC glue at home but not sure if that's appropriate (it's pretty potent stuff).
I guess the glue depends on what type of plastic these parts are made out of, which I have no idea about. It seems like pretty "standard" plastic but not sure at all what it is and what glue to use, so any info would be great!
The installation otherwise is going well. I gutted the stock front door speakers and bolted on my new 6.5" RF speakers on them and have them ready to be installed (waiting on the wiring adapter to arrive from Crutchfield) and I will be installing some RF 6x9 speakers for the rear deck tomorrow. These will be powered by 20W RMS (the speakers are all pretty low RMS rated, 5-40 for the components and 5-65 for the 6x9 rears) from my new double-DIN JVC receiver). Can't wait to finish!
I guess the glue depends on what type of plastic these parts are made out of, which I have no idea about. It seems like pretty "standard" plastic but not sure at all what it is and what glue to use, so any info would be great!
The installation otherwise is going well. I gutted the stock front door speakers and bolted on my new 6.5" RF speakers on them and have them ready to be installed (waiting on the wiring adapter to arrive from Crutchfield) and I will be installing some RF 6x9 speakers for the rear deck tomorrow. These will be powered by 20W RMS (the speakers are all pretty low RMS rated, 5-40 for the components and 5-65 for the 6x9 rears) from my new double-DIN JVC receiver). Can't wait to finish!
#2
Prelude Owner
iTrader: (7)
Re: What kind of glue to bond EX coupe's tweeter pods to new tweeters?
Loctite Super Glue should do the trick:
If that is similiar to what you tried then a 2 part apoxy might be best. Can be found at local hardware stores, will have a hardening agent and the glue seperate.
Double sided tape may work also. 3M makes one that is rated for outdoor use that is very sticky. I have used it for exterior badges.
If that is similiar to what you tried then a 2 part apoxy might be best. Can be found at local hardware stores, will have a hardening agent and the glue seperate.
Double sided tape may work also. 3M makes one that is rated for outdoor use that is very sticky. I have used it for exterior badges.
Last edited by GolNat; 05-27-2014 at 04:43 AM.
#3
Registered!!
Thread Starter
Join Date: Apr 2011
Location: Seattle, WA
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: What kind of glue to bond EX coupe's tweeter pods to new tweeters?
Loctite Super Glue should do the trick:
If that is similiar to what you tried then a 2 part apoxy might be best. Can be found at local hardware stores, will have a hardening agent and the glue seperate.
Double sided tape may work also. 3M makes one that is rated for outdoor use that is very sticky. I have used it for exterior badges.
If that is similiar to what you tried then a 2 part apoxy might be best. Can be found at local hardware stores, will have a hardening agent and the glue seperate.
Double sided tape may work also. 3M makes one that is rated for outdoor use that is very sticky. I have used it for exterior badges.
#4
*watches temp gauge like a hawkboss* :D
Join Date: Feb 2014
Location: Definitely older than ezone's skateboard. XD
Posts: 610
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 130 Re: What kind of glue to bond EX coupe's tweeter pods to new tweeters?
h4ldol, I have a '00 Suzuki SV650 that I installed an aftermarket gauge cluster on... which required a pickup sensor on the rear disc rotor and swingarm. Used a plastic epoxy from Loctite that held that plastic sensor on a steel swingarm through 10 degF days, soaked in sloppy Seattle weather, then 95 degF summers, no problem. If I were looking for a super-tough flexible epoxy, that would be the one to get. I'll see if I can find a pic or link for it...
#5
*watches temp gauge like a hawkboss* :D
Join Date: Feb 2014
Location: Definitely older than ezone's skateboard. XD
Posts: 610
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 130 Re: What kind of glue to bond EX coupe's tweeter pods to new tweeters?
Think it was actually Permatex -- their 5 Min Plastic Weld.
#7
Registered!!
Thread Starter
Join Date: Apr 2011
Location: Seattle, WA
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: What kind of glue to bond EX coupe's tweeter pods to new tweeters?
Thanks, everyone. I ended up using Loctite Plastic Bonding System which is specifically designed for hard to bond plastics, e.g. polypropylene and polyethylene. It seems to have worked well enough as the tweeter pod is sticking in the trim piece, although I haven't actually tested to see how much pressure it can take.
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
rayman7
Mechanical Problems/Vehicle Issues and Fix-it Forum
4
06-20-2015 09:48 PM
Bigdaddy198
Archive - Vehicles for Sale/Wanted
0
04-30-2015 08:36 PM
ademarco6
I.C.E. (Audio) & Electrical Upgrades
3
11-16-2001 10:19 PM
ademarco6
I.C.E. (Audio) & Electrical Upgrades
0
11-12-2001 06:52 PM