cutting the bumper?
#1
Registered!!
Thread Starter
Join Date: Jan 2009
Location: New York
Age: 32
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 cutting the bumper?
yea so i did some exploring and found a lot of threads about how to install fog lights for 01-03 civics. my problem is not so much figuring out how to wire up the lights but cutting the holes in the bumper...
i cant seem to find any threads that help out with this part of hte installation.
i dont have the "templates" that are mentioned in that official installation instruction thing and i dont wanna screw anything up lol
how do i know how big im supposed to cut these holes?
i cant seem to find any threads that help out with this part of hte installation.
i dont have the "templates" that are mentioned in that official installation instruction thing and i dont wanna screw anything up lol
how do i know how big im supposed to cut these holes?
#5
Registered!!
Thread Starter
Join Date: Jan 2009
Location: New York
Age: 32
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 0 Re: cutting the bumper?
AWESOME! thanks! this is exactly what i was looking for lol
but i still have some questions...
why doesnt the yellow line on the inner edge just match up with the red one?
also the previous owner of my car installed some universal fog lights and that may* have required him to cut out all of the grey plastic in the corners
would there be any problems if that tiny protrusion of grey plastic is missing?
*im not entirely sure about this i have to take a closer look at my bumper lol
but i still have some questions...
why doesnt the yellow line on the inner edge just match up with the red one?
also the previous owner of my car installed some universal fog lights and that may* have required him to cut out all of the grey plastic in the corners
would there be any problems if that tiny protrusion of grey plastic is missing?
*im not entirely sure about this i have to take a closer look at my bumper lol
Last edited by KevKevBarkBark; 03-31-2009 at 11:13 PM.
#7
Registered!!
Join Date: Jun 2007
Location: Tennessee
Age: 34
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 208 Re: cutting the bumper?
The yellow lines are from a picture somebody else put up just cut on the red lines and around the traingle thing
It depends on how much he/she cut out. If they cut out too much you may need to reinforce the foglight. This is how much plastic the fog lights will cover up:
Here is a PDF on how to install them:
http://www.handa-accessories.com/civic/civfglts01.jpg
also the previous owner of my car installed some universal fog lights and that may* have required him to cut out all of the grey plastic in the corners
would there be any problems if that tiny protrusion of grey plastic is missing?
would there be any problems if that tiny protrusion of grey plastic is missing?
Here is a PDF on how to install them:
http://www.handa-accessories.com/civic/civfglts01.jpg
Last edited by wallydude03; 04-01-2009 at 12:17 AM.
#9
Registered!!
Join Date: Aug 2005
Location: Ottawa
Posts: 2,551
Likes: 0
Received 0 Likes
on
0 Posts
Rep Power: 253 Re: cutting the bumper?
You should cut the yellow box instead of the red. If you need to cut more cut a little at a time afterward. It is not necessary to cut all the way out to the red line.
#10
Premium Member
Hey! Look At Me!! I'm a Supporting Member!!
iTrader: (14)
Join Date: Aug 2006
Location: Portland, Oregon
Age: 39
Posts: 8,362
Likes: 0
Received 1 Like
on
1 Post
Rep Power: 364 Re: cutting the bumper?
^^^ WORDS... you dont even need the templates. Cut until it fits, dont cut any more then you have to.
Thread
Thread Starter
Honda Civic Forum
Replies
Last Post
Wankenstein
Mechanical Problems/Vehicle Issues and Fix-it Forum
11
09-27-2015 11:33 AM
curaze
Mechanical Problems/Vehicle Issues and Fix-it Forum
3
09-22-2015 08:27 AM
MichaelLW
Fuel, Oil, Cleaners & Other Maintenance
2
09-14-2015 07:15 AM