Honda Civic DIYs and Civic Tech ChatHonda Civic DIYs and Civic Tech Chat - for the true gearheads! Bring your wrench, it's time for some Honda Civic DIY projects! Questions about problems with your car do NOT go here.
Welcome to civicforums.com!
Welcome to civicforums.com.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to start new topics, reply to conversations, privately message other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join civicforums.com today!
Materials:
5/16" or 3/8" Stainless Steel Screws
2" x 1/8" Thick Aluminum Bar
Tools:
Metal File
Jig Saw or Hack Saw
Sander or Sand Paper
Rubbing Compound or Steel Wool
Quick Clamps
Socket Set
Drill and Drill Bits
Countersinking Bit
These are the little screws that I bought for my head unit. I haven't tested them to see if I chose the right ones yet. I have over a hundred of them, so I chose to use them for tis project. As you can see, size 8, thread size 32, flat head, phillips screw.
The first thing you should do is take off the stock plastic door sills. We will be working with them outside of the car. That is unless you want to risk drilling into the metal? To be able to take them off (at least in the coupe) we have to take off the lower seatbelt attachment bar. Simply unbolt it using the proper socket.
Let's start on the passenger side. First take off the small piece that is closer to the front of the car. Here is what it looks like underneath. It's only held in place with two white clips. You could be able to figure out how to take it off by looking at this picture.
Next is the long piece. See all the clips? You'll have to be careful not to damage them. Don't pry with too much force. Remember where each clip is and try to get them all to pop out before you take the whole piece off. The end near the plastic panel in the back will be tricky to get out and even trickier to get back in.
This is what it looks like under the small piece.
This is what it looks like under the large piece.
Now for the drivers side. First take off the cover for the lock. Then take out that golden screw.
Now, what I did was push up this lock mechanism to disengage it from the lower portion. Otherwise I think that it would get in the way when trying to remove this plastic door sill on the drivers side.
This is what the small driver's side piece looks like.
This is what the large driver's side piece looks like.
Now that you've got that stock door sill out of the car you can use it as a template for the aluminum door sill. Simply cut the aluminum bar to the right length. Then round the corners so that they match the rounded corners of the stock door sill. Use a file to do this and compare it to the stock door sill by placing the aluminum bar on top of it.
After that's done take two clamps and clamp the aluminum bar to the stock door sill. Take care not to clamp down on one of the little white snaps on the underside of that plastic piece. I used paper towels here so that I would not scratch up the aluminum. I was also comparing it here in this picture to see what it would look like.
Now take a drill with that countersinking bit and drill holes through the aluminum and the plastic. My countersinking bit already had a regular drill bit on top of it. I used a somewhat broken up pattern so that the eyes would be fooled and not see any imperfections in the hole placement. Just be sure not to drill down too far. One mistake could cost you the project.
After the drilling has bean done you're ready to sand the piece down. Sand the rough edges, sand the countersunk edges, sand everything. Start at a lower grit, then move up to a higher grit. I finally used rubbing compound to polish the piece. I ended up with a nice satin sheen. I had to wash the piece down to remove the dirty rubbing compound. You could wet sand as well.
Then simply screw the piece down with those stainless steel screws and you're ready to go. Just reinstall everything first. I guess it might be easier to reinstall everything first and then screw down those pieces. Although if you buy the longer screws you can use washers and nuts on the underside to further secure the piece. I will make this switch later.
To remove this ad, register today for free or log in if already registered!
Sponsored Links
To avoid seeing this ad in our forum please register at CivicForums.com
By joining our free community you will have access to post topics, respond to polls, upload content and access many other special features.
No such thing. You'de have to anodize it yourself. Hey, good idea! I might do that myself. [IMG]i/expressions/face-icon-small-smile.gif[/IMG]
Check this out: Anodizing Aluminum
Thanks for all the comments guys. The drivers side turned out even better since it was the 2nd one I made. I originally wanted to make them look eactly like the stock plastic sideskirts with those two grooves, but I'de need a milling machine for that. I was also thinking that drilling out holes and sticking in flat rubber washers might look good. Especially if I had pedals that looked like that. Anyway...
Quote:
Quote
[hr]Originally posted by: 1siksivik
hey grey are their door sills out for our car or we have to do something like you did. great job by the way.[hr]
I'm not sure? I haven't seen any for coupe's. I've seen some for sedans that looked gross though.
Quote:
Quote
[hr]Originally posted by: thx1138
First Grey, your sill looks very nice Much better then my OEM ones.
Don't they sell the OEMS ones in the US/Canada ?
[hr]
Those are very nice. Are those CF or something? How much do they cost?
Quote
[hr]Originally posted by: thx1138
First Grey, your sill looks very nice Much better then my OEM ones.
Don't they sell the OEMS ones in the US/Canada ? [hr]
Those are very nice. Are those CF or something? How much do they cost?[hr][/quote]
They're about $70. They're not CF. I think it's a very thin piece of alu, with a plastic coating. It's not screwed on, just stuck with some d-sided stuff. Up close, it looks more plastic than metal. A bit cheap, to be honest. But my car came with them in a complete package from the dealer. Like I said, yours look much cooler. Wouldn't it be cool if you drilled/CNC'ed the word Civic somewhere in the middle, and painted that part. Not easy though.
Yeah, that would be the ultimate. No CNC machine though!
Then anodize it. Oh yeah, that would be nice.
I might save up for some anodizing equipment.
Shouldn't be more than $50. [IMG]i/expressions/face-icon-small-smile.gif[/IMG]
I took a look at your ride this morning and saw those and was wondering when you were gonna put up a DIY.
I gotta see those in person. they look wicked nice from the pics.
