E-Manage FAQ!!!!!!!!!

[HyaBoosta]

Ok I found my problem. I updated the firmware and support tool but when I try to update the main unit it will either say corresponding please wait or it will start to update and cut off after 27 sec and say update failed. Any ideas? It says that the support tool is online too.

To remove this ad, register today for free or log in if already registered!

[dezod]

Originally Posted by HyaBoosta

Ok I found my problem. I updated the firmware and support tool but when I try to update the main unit it will either say corresponding please wait or it will start to update and cut off after 27 sec and say update failed. Any ideas? It says that the support tool is online too.

So what firmware are you running?

Did you update the support tool?

[HyaBoosta]

the support tool version is saying v.1.13 (I used the update in the link in this thread)
and I downloaded the firmware but when I get to the point when I update the main unit and click on the new firmware to update thats when it just says corresponding or fails after 27 sec. and the upload only goes 1/2 way

[dezod]

Originally Posted by HyaBoosta

the support tool version is saying v.1.13 (I used the update in the link in this thread)
and I downloaded the firmware but when I get to the point when I update the main unit and click on the new firmware to update thats when it just says corresponding or fails after 27 sec. and the upload only goes 1/2 way

THAT'S WEIRD.

[HyaBoosta]

wurd^^

[HyaBoosta]

got it fixed but I can't find the rpm wire. in the write up it says it's the blue wire in connector A in pin 7 but in the wire write up it says\
Connector A (31 Pins)
1-blk/wht-Primary O2 sensor heater control
2-yel/blk-Power Source
3-yel/blk-Power source
4-blk-Power ground
5-blk-Power ground
6-wht-Primary O2 sensor
7-blu-Crankshaft position<-------?
8-yel-Sensor return volt
9-red/blu-Knock sensor
10-grn/yel-Sensor ground
11-grn/wht-Sensor ground
12-blk/red-Idle air control valve
13-wht/blk-EGR Valve position VTEC ONLY
14-blk/wht-Secondary O2 sensor heater control
15-red/blk-Throttle position sensor
18-wht/grn-Vehicle speed sensor
19-grn/red-MAP Sensor
20-yel/blu-Sensor Voltage Supply
21-yel/red-Sensor Voltage Supply
23-brn/yel-Logic ground
24-brn/yel-logic ground
25-wht/red-Secondary O2 Sensor
26-grn-Top dead center sensor
27-brn-Igniton coil 4
28-wht/blu-coil 3
29-blu/red-coil 2
30-yel/grn-coil 1

[abmerop18]

the rpm wire is also int he engine bay if you dont wanna search for it in the connectors. it is a blue wire by the passenger side headlight

[dezod]

Originally Posted by HyaBoosta

got it fixed but I can't find the rpm wire. in the write up it says it's the blue wire in connector A in pin 7 but in the wire write up it says\

What write up?

[abmerop18]

hya - what did you do to fix it? mine is doing the same thing now

[HyaBoosta]

does it say online on the bottom of the support tool? did you update the main unit with the .p file?

[abmerop18]

it says online, but it still says that even when the support tool is unplugged

i am trying to update the main unit, but it is trying to connect with it and it just keep on going, but it never does anything.

[C2i0v0i1C]

new emanage forum

link is in this thread
http://www.7thgencivic.com/forums/sh...d.php?t=193954

[abmerop18]

Lookin at the diagram, for the input on the ignition harness, that goes go the ECU and the output goes tot he e-manage, right?

[abmerop18]

^ the answer to that is yes because i just wired it up and it is working now

[exturbo6]

k i got my e-manage. and i opened it to see what it was all about and i saw a boost thing you clip in. what goes into that? do i need to buy somehting else, or will whatever i have for my turbo kit clip into that? thanks