Honda Civic DIYs and Civic Tech ChatHonda Civic DIYs and Civic Tech Chat - for the true gearheads! Bring your wrench, it's time for some Honda Civic DIY projects! Questions about problems with your car do NOT go here.
Welcome to civicforums.com!
Welcome to civicforums.com.
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to start new topics, reply to conversations, privately message other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join civicforums.com today!
After a few back-breaking hours trying to install this thing, I thought I would share my results. Some of those grounding points were extremely difficult to get to and get the bolts back on. On top of all that, a bolt fell into the engine bay somewhere and I had to drive to Honda for another one. Craziness!! I wired mine the same way Happies did in the first post of this diy. The only difference was I used the tranny bolt near the dipstick because the stock grounding point bolt would not come off. All other connections are the same.
Here are the results, which were somewhat disappointing at first. The car started up fine, like it always does, and I didn't feel that it was any faster than before. So the engine didn't improve. While driving around, it maybe felt like the auto tranny was shifting a bit smoother. The headlights didn't really look brighter, and there was no increased throttle response. When I turned on the stereo, I noticed that the subs were alot louder than before. I had to turn down the level a couple notches on the deck to have it back to what it was before.
Overall, it seems to have helped with the electrical system a bit and maybe the tranny shifting. I think this alone makes the kit worth it, especially for just $38.
Thanks, Happies, for the 1-week shipping and a good product!
Originally posted by happies713 You can do either method. from A to B to C. tha is the Daisy Chain method, works very good, its the most used method by the people who buy my kits.
you can also to neg to A, neg to B, neg to C. i dont really know if this is better, but it also works good!!
hm...u r not sure about it?
i just thought second method works better since its directly connected from neg terminal..
but if most ppl go with daisy chain method, then it doesnt matter for me
Use the daisy-chain method. It works. You'll probably notice the most improvement with the stereo. I didn't see much performance gains, and I went into this project with high expectations. Still worth it.
Originally posted by gearbox Use the daisy-chain method. It works. You'll probably notice the most improvement with the stereo. I didn't see much performance gains, and I went into this project with high expectations. Still worth it.
same here ........ but i didn't buy it from happies713 .... DIY from left over wires
The only spot I needed to shave was the valve cover bolt, since the bottom was painted. All the rest were good (bare metal). I would run all the wires first and attach them to the negative terminal LAST. That way you won't have to take out the connector and lose radio settings and stuff.
ok i changed my configuration a bit...instead of neg battery directly to firewall i used another wire to go from neg battery to stock trans ground to firewall...
had the chance to drive around more today...lights are brighter...stereo sounds much better..car seems to run a little smoother...the exhaust note isnt as "rough"...auto tranny shifts quicker... oh ya...and windows go up and down faster...lol no joke
no you dont have to disconnect the battery...i just took the bolt out of the neg terminal without actually taking the negative terminal off...resetting the ecu is a good idea but it makes it harder to notice any gains because the ecu's fuel/ignition maps are reset...
ok, I just finished my grounding kit install! I've noticed benefits all around, mainly brighter lights, in and out, and my stereo is now THX certified here's my version:
from negative to transmission:
from transmission to firewall:
from firewall to right side strut tower:
now, for this next part, i went from the negative terminal to the radiator support frame, then channeled out by cutting the largest wire into 2 pieces:
I heard all you had to do was shave the paint off the valve cover nut, but i decided to shave all the contacts I was making to the frame of the car. and sure enough, the firewall, the strut tower, and the radiator frame all had a painted finish.
here's my version:
