[speedfoos]

Who's POS is that?

[FoSho]

I can see the picture just fine....it's bitch wine...for you beotch!
Just remember clint....you may have beat me to engine build but I'm going standalone before you sucka! K-PRO Bought chump!! :P

[filipinop1405]

Originally Posted by speedfoos

Who's POS is that?

fuck you clint... its mine fucker!!!

[lordhelmet]

Originally Posted by speedfoos

Future plan is to ditch this chassis and get a clean ES1 chassis and swap all my goodies into it. There is too much body work and paint to be done on this car to be cost effective. I can pick up a rolling chassis for much cheaper than fixing this one, plus it would be less work as well.

Your car is looking spiffy once again Speedfoos!

Glad to have you on the ES1 bandwagon. Coupes are fucking worthless. Two doors should always be equal to two seats.

[speedfoos]

Originally Posted by FoSho

I can see the picture just fine....it's bitch wine...for you beotch!
Just remember clint....you may have beat me to engine build but I'm going standalone before you sucka! K-PRO Bought chump!! :P

Well at 0700 this morning when real men are up and doing stuff, it was down. It's not my fault you chose to link a picture from a weak sauce website Avery! Plus how long is it going to sit in your office before you get off your dead ass and install it?

You can't handle this stuff son. Best sit down.

Originally Posted by filipinop1405

fuck you clint... its mine fucker!!!

Heehee! Changed my mind then. I'll just wait till you get demoted, can't afford to pay all the bills and then swoop in like a buzzard and buy your car for $3. Then I'll build it the right way!

Originally Posted by lordhelmet

Your car is looking spiffy once again Speedfoos!

Glad to have you on the ES1 bandwagon. Coupes are fucking worthless. Two doors should always be equal to two seats.

LOL! Thanks, it's going to be a little while before I get to it. I've got to put Jay in some compromising situations and then get the photographs to his command before I can buy his car.

[FoSho]

aww....can't post...

[FoSho]

Shit son...I open the shop @ 7 am and start fixing cars...I'm still here when you get off sucka! and yes it will probably sit in my office for a couple months....I'm broke, you know how expensive it is to tune that shit!!!....

who needs there car fixed!!!!! Greater KC/MO area...hit me up!! I need a paycheck!!!! I just got hit by a tornado...can I get some diaster relief????

[filipinop1405]

naw aint gonna happen clint!!

oh yea real men get up @ 0500-0530 bitches!!!

[speedfoos]

I don't have to get up at 0500. Ever.

I here ya on the fundage Avery, k-pro is my Christmas present.



Discovered my winter project though! Gonna paint up my Konigs because the clearcoat is all fucked up on them. Depending on how they look when I put them on the car, there's a good chance I won't be buying the HFPs. So first I grabbed the old one sitting in my office which has a a bunch of curb rash. I wiped it down with some acetone so the primer would stick and then primered it.




If I cared about the results I would have stripped the old paint and clear off the rim and then sanded it down, but I just wanted to see how it looked all black.

Then I mixed up a mix of about 8:1 thinner to Rustoleum black outdoor enamel and shot it outside with my paint gun. Didn't turn out too bad! In fact I think I like it a lot and will probably paint the rest of them this winter!

[FoSho]

Damn I've never seen rustoleum look so good....how does it hold up though? I know they make alot of "wheel" paints that are resistant to rust, heat, & chipping.........You guys got aeromotive paint stripper over there? I get it at orielys....10 minutes on the metal and the paint is completely gone! Just spray with water and viola! I swear by that stuff!

[FoSho]

Damn I've never seen rustoleum look so good....how does it hold up though? I know they make alot of "wheel" paints that are resistant to rust, heat, & chipping.........You guys got aeromotive paint stripper over there? I get it at oriellys....10 minutes on the metal and the paint is completely gone! Just spray with water and viola! I swear by that stuff! But I'm a mechanic...not a painter...so I'll probably be taking advice from you......My coating came off my wheels yesterday too

[speedfoos]

Doublepost FTW!!! That Rustoleum lays down really well when you thin it and shoot it through a paint gun. I usually use ZipStrip aircraft paint stripper when getting the heavy stuff off. Same concept, brush on and spray off with water. Stuff gave me a nasty chemical burn on my arm when I didn't rinse it off in time. Mr. Durden would have been proud! As far as how it holds up.....it's the same stuff I painted my car with last year and that's holding up fine!

[FoSho]

I don't know why it double posts like that...must be my work computer.

I think I might have misread you....did you say you painted your car in rustoleum? ahaha.....you're friggin redneck! You must be from the midwest!

I got this picture when I searched for rednecks...haha! I thought it was hilarious

[filipinop1405]

it looks pretty good clint!

[speedfoos]

LOL - yes I did paint with Rustoleum Avery! And I was born in Upper Michigan, so eat me! The body is so far gone on this point (hence the plan to swap to an ES1 chassis with a clear title) that I just want some paint on her. As you can see from how well the rim paint laid down with no prep, the car actually looks decent. I used a regular automotive clear coat on it as well.

Thanks Jay!